Question 7 The antenna tower is supported by three cables. If the forces of these cables acting on the antenna are FB = 520 N, Fc = 680 N, and Fp = 560 N detemine the magnitude and coordinate direction angles of the resultant force acting at A.

Q: 1-) b. 1+j 1 Evaluate a. 1+j

A: Ans(a)  j2=-1 Divide by 1-j both sides 1-j1+j×1-j1-j (1-j)21-j2=1+j2-2j2=-2j2=-j

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: What is the value of w and y? y W 6V2

A:

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: Question 1 Johnny has recently purchased 110 acres of land in New Zealand. He has decided to grow…

A:

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: QUESTION I ) Sute True or False for the following statements: O The principal stresses represent the…

A: Disclaimer: Since you have asked multiple questions we will solve the first one for you. If you want…

Q: Draw chalk diagram of all sections

A: To draw section views

Q: 11 .625 .125 SECTION A-A VIEW B-B .344 1.000 .313- 0.2407+.0013 -.0013 10 .125 8 B A Q 3.875 NO…

A: Given: Name these lines.

Q: A hydro-electric dam uses turbines to generate electricity as reservoir over the turbine blades. A…

A: (a) To fill: The blanks of the statement with appropriate choice. Explanation: Hydroelectric dam: A…

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: Determine ly and ky.

A:

Q: u 30° 40° F = 600 N 22

A:

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: tan 0 2. lim 8 -0 sin 20

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: Which best represents the Slope-field and streamlines for dy = y? – 9 dt

A:

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: Which of the following statements below are incorrect? select all which apply.     A shear force…

A: It is needed to provide the wrong or incorrect statements.

Q: When installing an air conditioner in a car, hose with a diameter of 2.5centimeters is used. Each…

A: Air conditioner is a device used to produce cooling by dissipating heat in the form of fluid or…

Q: Find the value of x5 in 1 decimal places (positive value) using Newton-Raphson Method f(x) = 2x2 + x…

A:

Q: Two forces are acting at an angle of 180°. The bigger force is 80N and the resultant is 40N and…

A:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.