QUESTION 7 Suppose we have a ship in the ocean (water sp.gr - 1.034). The ship has freeboard (height of decks above water of 20 m. The draft is also 20 m... (distrance from bottom of keel to surface of water. Ship is rammed by som projectile at 10 m below waterline. The hole is 5 m². At what rate does water flood the ship? (m³/sec)

QUESTION 7 Suppose we have a ship in the ocean (water sp.gr - 1.034). The ship has freeboard (height of decks above water of 20 m. The draft is also 20 m... (distrance from bottom of keel to surface of water. Ship is rammed by som projectile at 10 m below waterline. The hole is 5 m². At what rate does water flood the ship? (m³/sec)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution with clear calculations
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
Hydraulic Structures ضخبعزيزي
A small orifice 0.0003 m³ in area is in the vertical side of a rectangular tank. The horizontal sectional area of the tank is 0.40 m². At a given instant the head on the orifice is 1.2 m and 312 sec later it is 0.6 m. Compute the value of the coefficient of discharge C. (5 pts.) Using a coefficient of discharge of 0.60, how long will it take to lower the water surface from 1.2 m to 0.80 m. (5 pts.) Using C=0.60, what will be the heigh of water from 1.2 m after a lapse of 240 sec. (5 pts.)
Two pipes connected in parallel having a total discharge of 0.05 cu. m/s If pipe A has a total head loss of 0.5 m whose length and diameter are 200 m and 150 mm respectively. Pipe B have a length of 100m and diameter of 200mm. If they have the same friction factor f = 0.02. Compute the discharge at pipe Ba. 0.04 cum/s b. 0.01 cum/sc. 0.02 cum/sd. 0.03 cum/s
correct answer only
Question 1 An anaerobic waste stabilization pond is treating poultry wastewater with following design data; 225 Alder Aerial Organic Loading- 500 kg BOD5/ha.day BODs load - 3,500 kg/day 3.v Depth - 2 m BOD-20,000 mg/L Assume no side slope. Calculate: (i) Volume of tank Dl = Disch & BOD ол prch= (ii) The incoming flow in m³/day sl всь 500 20000
???
9:35 回M回 O NI lal 98% IMG 20220311 093254.jpg The total headloss from A to D is 9 m. Using f 0.02. L=450m D=300mmg A B D L=450m D=450mmø L=200m D=200mmø L3600m D=450mmø L=480m D=250mmø O Compute the discharge of pipeline 3. ® Compute the discharge of pipeline 1. O Compute the discharge of pipeline 4. O Compute the discharge of pipeline 2.
Design a rectangular prism water tank having the following conditions:a. The volume of the tank must be 96 cubic feet.b. The base length must be 4 ft more than the base width.c. The height of the tank must be 2ft more than the base length.
subject: hydraulics engineering
A 300mm x 300mm pipe discharges 600 L/s of water where the length is 30m. Determine the head loss if f = 0.021 hf = 83.412m hf = 72.126m hf = 86.246m No answer among the choices hf = 68.921m hf = 77.093m