A 6cm diameter horizontal water pipe expands toa 10cm diameter pipe. The average velocity andpressure of water before the expansion sectionare 7 m/s and 150 kPa, respectively. Determinethe pressure in the larger diameter pipe. UseTable 2 from our Lecture for the loss coefficient.A162 КPaВNone of the aboveC) 168 kPaD) 171 kPa Table 2. Values of KeRatioVelocityVeD1/D20.5(m/s)0.600.00.10.20.30.40.60.70.80.90.040.040.041.001.00.960.860.740.600.440.290.150.960.950.890.800.690.550.410.390.370.350.270.261.500.143.000.910.890.840.760.650.520.130.500.476.000.860.840.800.720.620.240.120.0412.000.810.800.750.680.580.220.110.03

Answered: Image /qna-images/answer/6d91445b-7e98-496e-a146-065d30c9cf13.jpg

A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the pressure in the larger diameter pipe. Use Table 2 from our Lecture for the loss coefficient. A 162 kPa В None of the above C) 168 kPa D) 171 kPa

A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the pressure in the larger diameter pipe. Use Table 2 from our Lecture for the loss coefficient. A 162 kPa В None of the above C) 168 kPa D) 171 kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

15. If the pressure in pipe A is 6 kPa, the SG = 0.85 pressure in pipe B =. ........... psig. Water 90 mm 30% a. 1.27 70 mm b. 8.73 40 mm C. 60.17 SG = 13.6 Mercury d. None of all these
Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.
Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).
1- Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of diameters 10.16 cm and 5.08 cm with a smooth reducing section. The pressure difference between the two pipe sections is measured by a mercury manometer. Neglecting frictional effects, (a) determine the differential height of mercury between the two pipe sections. (b) How would the reading change if the manometer on the 2in pipe is replaced by a pitot tube? 10.16 5.08 h
3. What is the pressure difference between pipe A and pipe B? Give pressure difference in kPa. (y = 1.22 m and h 30 in.) The gage fluid, M, is mercury with a specific gravity of 13.54 State assumed values if any. Water A Water B y D Liquid M
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
Determine the friction loss if the friction factor is 0.4 and velocity of the flow is 40 m per sec. Given length of the pipe is 20m, inner diameter 0.3m. Use friction loss formula. Using the calculated friction loss, solve for the ffg: a. What is the pressure drop due to the Bernoulli effect as the water goes into a 3.00-cm-diameter nozzle froma 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? b. To what maximum height above the nozzle can this water rise? (To actual height will be significantly smaller due to air resistance.)
A 25-mm-diameter pipe 35m long is used to convey oil. The oil has a density of 880kg/m³ and a kinematic viscosity of 0.25×10*m³/s. The discharge in the pipe is Q=24x10*m³/min. Given that the pipe is placed horizontally and there are no any minor losses. Determine the pressure drop between the entrance and exit of pipe.
At Point A, in a pipeline carrying water (y=62.4 Ib/ft^3) the diameter is 4.0 ft, the pressure is 10 psi, and the velocity 4 ft/s. At point B, 6ft higher than point A, the diameter is 2 ft and the pressure is 2psi.determine the following:(a)quantify the losses in this system and (b) is the flow going from Point A to Point B or from point B to point A. why?