An (ideal) Otto cycle with air as the working fluid has a compression ratio of 8.7. Under cold-air-standard conditions, the thermal efficiency of this cycle is most likely: 58% 10% 39% 79% 95% QUESTION 7An (ideal) Otto cycle with air as the working fluid has a compression ratio of 8.7. Under cold-air-standard conditions, the thermal efficiency of this cycle is most likely:58%O 10%39%79%95%

Answered: Image /qna-images/answer/887803ce-fb3d-427f-ab2f-bba34fcb36b7.jpg

QUESTION 7 An (ideal) Otto cycle with air as the working fluid has a compression ratio of 8.7. Under cold-air-standard conditions, the thermal efficiency of this cycle is most likely: 58% O 10% O O 39% 79% 95%

QUESTION 7 An (ideal) Otto cycle with air as the working fluid has a compression ratio of 8.7. Under cold-air-standard conditions, the thermal efficiency of this cycle is most likely: 58% O 10% O O 39% 79% 95%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How does the a Regenerative Rankine Cycle improve the simple rankine cycle? How much improvement in efficiency is gained? What are the disadvantages of a Regenerative Rankine Cycle? What are the Difference of a Open Heater to a Closed heat exchanger?
An ideal reheat Rankine cycle with water as the working fluid operates the inlet of the high-pressure turbine at 7000 kPa and 450°C, the inlet of the low-pressure turbine at 500 kPa and 500°C, and the condenser at 10 kPa. Determine the mass flow rate through the boiler needed for this system to produce a net 5000 kW of power and the thermal efficiency of the cycle. Use steam tables. kg/s. The mass flow rate through the boiler needed for this system to produce a net 5000 kW of power is The thermal efficiency is %.
Question 1 A simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 30 kPa. The boiler produces a 10 MPa superheated steam at 450°C. The isentropic efficiency of the pump and turbine are 100% and 90% respectively. Calculate, (a) the heat supplied in the boiler. (b) the work produced by the turbine. (c) the quality of steam at turbine exit (d) the thermal efficiency of this cycle. Pump 0-1 Boiler 10 MPa 450 deg C 0 Turbine Condenser O 30 kPa
An ideal Otto cycle with air as the working fluid has a compression ratio of 8. At the end of the heat rejection process, temperature decreases to ambient temperature (25 Celsius ) and at the end of heat addition process temperature increases to 1107 celsius. Use air standard assumption and calculate the following quantities. (a) the amount of heat transferred to the air during the heat-addition process (8) (b) the thermal efficiency (8) (c) the thermal efficiency of a Carnot cycle operating between the same temperature limits
Consider an ideal Rankine thermodynamic cycle with H2O as the working fluid. From the following data calculate all heat andwork flows (including the back work) for the cycle and the overall thermal efficiency. Data: h1= 385 kJ kg–1specific enthalpy h2= 388 kJ kg–1 h3= 3,115 kJ kg–1 h4’ = 2,663 kJ kg–1 saturated vapour x4= 0.89 steam quality
A gas-turbine power plant operates on the simple Brayton cycle with pressure ration of 16. The working fluid (air) enters the compressor at 40°C and 1 atm with a rate of 850 m³/min and leaves the turbine at 650°C. Assuming a compressor isentropic efficiency of 85 % and a turbine isentropic efficiency of 88 %. ********************************* *********** ****** Note the following: ideal gas equation of state: Pv = RT,PV = mRT, P2V2 P,V1 %3D T2 T1 k-1 T2 ideal gas undergoing an isentropic process: T1 constant specific heats and gas constant with: %3D kJ = 1.108: kg · K' kJ C, = 0.821 kg · K' kJ R = 0.287 kg · K Gp k = 1.35, Draw or calculate: (a) a "T-s" or "P-v" diagram that represents this Brayton cycle. (b) the outlet pressure (kPa) of the compressor. (c) the outlet temperature (K) of the compressor. (d) the inlet temperature (K) of the turbine. (e) the mass flow rate (kg/s) of the cycle (hint: use the equation of state). (f) the power (kW) of the compressor. (g) the power (kW) of…
The digital thermometers that we use in the lab today are similar to the ones that we use in our homes, but several years ago scientists used to use glass thermometers that contained a thin column of mercury to measure temperature. Why do you think we no longer use the mercury thermometers in the lab?