Question 7 A simply supported beam made of timber is shown; determine the minimum required width b, knowing that for the grade of timber used the maximum allowable shearing stress is 825kPa. RA 2.4 kN B 4.8 kN -1 m- +-1m- Figure AQ7 11.4 Ro 150 mm

Question 7 A simply supported beam made of timber is shown; determine the minimum required width b, knowing that for the grade of timber used the maximum allowable shearing stress is 825kPa. RA 2.4 kN B 4.8 kN -1 m- +-1m- Figure AQ7 11.4 Ro 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The nails are on both sides of the beam and each can resist a shear of F. If the beam is subjected…

A: as we can know that maximum shear will occur at AB of a vlaues V(max)=(P+4.5)KN

Q: Please show clear and complete solutions. Box the final answers. Note: The tolerance is ± 1 in the…

A: The truss with the loading and support conditions is given as To find:- Force in members BG and BF

Q: V brauw qualitalíve shear, and, moment diagrams for Hais beam.

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: V 6-3 A beam with an overhang is supported and loaded as shown in the figure. The beam is made of a…

A: Beam: Channel section: No. 14 b steel channel To find: The maximum tensile and compressive stress…

Q: 2 - For beam I with distributed and concentrated loads, determine: a)The maximum shear stresses…

A: The FBD of the beam is shown below: Taking equilibrium equation: The SFD of the beam is shown…

Q: Determine the maximum flexural stress experienced by the beam in MPa. Determine the maximum shearing…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: ch material at point H, which is located at a distance of a - 1.4 in. above the zo

A: data we have b = 1.1 in d = 6.0 in t =0.50 in ∈1 =2200 ksi∈2 = 28000 ksi Moduli ratio m = ∈2∈1…

Q: Design a welded plate girder of span 30m to carry imposed load of 25kN/m. Avoid use of bearing and…

A: Span=30 mImposed load=25 kN/mSteel grade= Fe 415 To design: welded plate girder

Q: te t for Tension and C for Compression). ]12 kN 4 m B 6 kN 4 m C E I K 6 @ 3 m

Q: 1) Reqd: Determine Maximum Shearing Stresses for the 3 segments and 0at C 2) F (2)Solid…

Q: 1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear…

Q: Total load 87 psf = B1W16 x 57 G1W24 x 68 Compute Vmax and Mmax for Beam 1 and Girder 1 in the roof…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: Montebon, Jamaica Mae B PIate No. lo Vir tyal Work Method (Trusses) ID NG. 16-0893-335 #1. Determine…

Q: P Bearing plate Let the allowable stresses in the post be ost=120MPaand oco=6MPA. Compute the…

A: Solution-The given data ,σst=120MPaσco=6MpaModulus of elasticity=200GPa and For concrete 14GPaCross…

Q: Ass #2. Solve the following Problems. 1. Using method of sections, determine the forces in members…

Q: Design a purlin for a roof truss having the following data: Span of the truss = 6.0m Spacing of…

A: Span of the truss = 6.0mSpacing of truss = 3m c/c.Inclination of roof = 30oSpacing of Purlin = 2m…

Q: the rectangular beam given in figure below has been designed for flexure; design the necessary shear…

A: It is required to determine the factored load. wu=1.2DL+1.6LL=1.240+1.625=88 kNm It is required to…

Q: a -1 in.- 0.25 in. B a

Q: 25 A P₁ 45 P2 no to 45 P2 25 P₁ 45 P2 E 6 panels @ 3.0 m = 18.0 m 43 P₂ K 25 P₁ 6.0 m

A: Solution: Here it is a symmetric section and the loadings also symmetrical. Hence it is enough to…

Q: Problem # 2: Determine the internal axial force in each member of the truss using the force method.…

Q: Problem 2: A bridge girder consists of W 760 x 161 and a channel C 380 x 50.4 and joined by 2 - 22…

A: Maximum bending stress in tension is the maximum stress experienced by the beam due to the applied…

Q: use method of members to get results of joints A to E

A: To find reactions at all points

Q: (a) Computer the bending stresses in beam by using transformed- for the all question area the…

Q: DEad LOAD = 1OKN LIVE LOAD: 12 KN DEADLOAD: 10 kN PEADLOAD= 10 KN LIVE LOAD: 8 kN LIVE LOAD = 10 KN…

Q: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P=210 kN. The…

A: A double angle tension member

Q: HAnd written and clean writing

A: Given data - A TrussFind out - Force in member AF ,BE, BF,CE ?

Q: Two sections of beam are clesigned to resist bending moment of Mx. () which section has a larger…

A: The moment of inertia is defined primarily as fluctuations or loss of volume due to the effect of…

Q: a 9 ● с B col 0.2 m m d FO F₁ F₂ A structure is contructed of three beams DABC, GDEF and HEB.…

A: Sign conventions and assumptions required to solve this strucutureDraw the free body diagram of the…

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

Q: Example 3 AT-shaped simply supported beam has the crass stetion shown in Figure PL4. It has a span…

A: Question is based on inverted T beam . Dimension of span and loading condition on beam is given in…

Q: 5- A beam is reinforced with Ø16 mm bars and Ø10@200 mm stirrups. If the concrete cover is 40 mm, f,…

A: Given: Diameter of reinforced bars= 16 mm Diameter of stirrups = 10 mm Spacing of stirrups= 200 mm…

Q: Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH= 1200N (C)…

A: To find member forces and value of load P1,P2,P3

Q: 2. Determine the maximum tensile and compressive bending stresses in the beam shown. -1"x6" -1"x4"…

A: To find the maximum tensile and compressive bending stresses in the given beam.

Q: Solve the given frame using Set 1(Portal Method)/ 27 kN 4 m 49 kN G 5 m K 6 m 4 m 8 m Determine the…

Q: For the given beam, plot Influence Line Diagram for shear at C. 3 m B. 3 m 3 m 2 m A,

A: When the unit load is at C - SF at C, VC = -RB = 35 = .6 Load at A - VC = -VB = 0 Load just to…

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

Q: Determine the force in member CD (in kN, round-off to 2 decimal places, include "-" if in…

Q: Problem NO. 2. Determine the force acting on members HI, HJ, GI. Also, the force acting on members…

Q: 3.4 The required flexural (bending moment) strength is of a reinforced concrete beam is Mu= 260…

Q: USE METHOD OF SECTIONS, SHOW COMPLETE SOLUTION WITH FBD: ompute the force in member GM of the loaded…

A: To find force in member GM

Q: 0:Design the steel reimforcement for flexural for the beam shown m the kN fig.below The dead load on…

A: if the size of beam is known and area of reinforcement is need to design then their is 2 cases 1-…

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assignment 5.2 -Steel Beam Analysis P-20 kips P-? kips W 24 x 76 A992 Steel The beam carries the following service dead load and live load 10h 20t P=20 kips P=? kips 30h Determine the maximum Lateral support is provided at both ends and at the load points service live load that the beam can carry, if the weight of the beam is neglected.
1.51 Link ACis made of a steel with a 65-ksi ultimate normal stress and has a X -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by -in.-diameter pins, while member BCD is connected to its support at B by a 16-in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.25 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 8 in. B D 6 in. 4 in.- Fig. P1.51
SHOW COMPLETE FBD
面包 EX Privi Tern ? Question Completion Status: F1 = 64 kN Refer to the truss as shown. Given: F2 = 83 kN F3 = 12 kN A 4 7 5 F B # LE F₁ -4m-4m 6 3 7 G LA C $ F₂ 4 9 H -4 m- Determine the axial forces in member GD (kN). Express your answer in 2 decimal places. Neglect sign if compression. 10 D % 11 5 F -4 m 12 A 13 E 14 15 4 m ∞0 7 16 17 hp 180 19 20 00
kindly solve only subpart LETTER D. with a complete solution for verification purposes. Thank you for your assistance!
2 kN The beam is made of three boards nailed together to form the double-T cross section shown. If the allowable shear force in each nail is 400 N, determine (a) the absolute maximum shear stress in the wood, B (b) the required spacing s, of the nails between A and B, 2 m 1 m (c) the required spacing sy of the nails between B and C. -150 mm- T25 mm 200 mm 25 mm 25 mm
Design a bridge truss diagonal subjected to a factored tensile load of 300 kN. The length of the diagonal is 3.0 m. The tension member is connected to a gusset plate 16 mm thick with one line of 20 mm diameter bolts of grade 8.8
AT-beam with bf-425mm, tf-100mm, bw-250mm, h-350mm, cc-30mm, stirrups 12mm is reinforced by 6-32mm diameter rebar as shown. Assume fc'-28Mpa, fy-345Mpa, calculate the following. 425mm Icon 17 350mm 6-32mm 250mm Strain of the bottom reinforcement Moment capacity of the beam _kN-m
Give me right solution with clear calculations
9-23. The wood beam is subjected to a load of 12 kN. If a grain of wood in the beam at point A makes an angle of 25° with the horizontal as shown, determine the normal and shear stress that act perpendicular and parallel to the grain due to the loading. |--2m-¹ 25° 12 kN 75 mm 4 m- 300 mm 200 mm
P 4 in. P Lin. 8 in. FIG. P1.55
Draw BMD and SFD for the beam shown below: 8 kN w 2 kN/m A 3 m B. 9 m 3 m Rp D.