Question 6 The Figure 6 shown below depicts the cavitation process that occurs in a gear pump showing how cavities generate, grow and collapse in fluid-type components. Analyse briefly this phenomenon in terms of its five (5) contribution factors. а. Surface Damage Cavity Collapse Cavity Growth Cavity Generation

Question 6 The Figure 6 shown below depicts the cavitation process that occurs in a gear pump showing how cavities generate, grow and collapse in fluid-type components. Analyse briefly this phenomenon in terms of its five (5) contribution factors. а. Surface Damage Cavity Collapse Cavity Growth Cavity Generation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. When the path of individual particles does not cross or intersect, the flow is said to be A. Turbulent C. Uniform B. Laminar D. Non-uniform 7. A Reynolds Number, Re = 1 x 10°, indicates that the flow is B. Steady A. Transitional C. Laminar D. Turbulent 8. Cavitation in fluid mechanics refers to A. The separation of the air flow behind a wing. B. The oscillations of a plate due to turbulent fluctuations. C. The liquid to gaseous phase transition of a fluid due to low pressure. D. The condensation of vapor into liquid due to high pressure. 9. Machines that involve the flow of fluid through rotors that remove or add energy to the fluid. A. Positive displacement machines B. Slider crank machines C. Reciprocating Machines D. Turbomachines 10-THe difference between the pressure at the pump suction and the vapor pressure of the liquid at the given temperature expressed as pressure head. A. Vapor Head B. Pressure Head C. Net Positive Suction Head D. Velocity Head
We give: AB: adiabatic trigger such as VB = 2 VA AC: isothermal compression PA =1bar=105 Pa , VA = 10^-2 m3 Gas temperature at point A: TA= 300 Kelvin Perfect gas constant: R = 8,31 J.mol-1.K-1 Molar thermal capacity at constant pressure:Cp = 29 J.mol-1.K-1 Calorific capacity ratio of this gas: Cp/Cv = 1,40 4 – Calculate the amount of QBC heat and WBC work received by the system for the transformation that changes the system from state B to state C.5 – a – Why is the UCA internal energy variation of the gas zero during the CA transformation? b – Apply the first principle to the ABCA cycle and deduce the WAB work received by the gas during theadiabatic relaxation AB.c – Interpret the WAB sign.
Thermodynamics
a 4 Exercise 7 -Opening and closing a boiler door for b) Calculate retracting speed, retracting time, travel speed ratio and travel time ratio. ictin Characteristic data required for calculation: Piston surface area: Ap = 2.0 sq. cm Piston ring surface area: APR = 1.2 sq. cm Stroke length: = 200 mm S Pump delivery rate: = 2 l/min b Retracting speed Retracting time Travel speed ratio Travel time ratio
a) A fluid with mass of (2,5+JM1)%m for volume of (3)cm’” . Calculate the mass density in (Kg/m’), (slug/ft’) and weight density in (Ib/ft’) and relative density of the fluid. b)Estimate the exit velocity of water from the shower head. The shower head contains 80 holes of (0.1)cm diameter. 3) d=15cm / (2) -— -~ () V2=0.25m/s +Juldlix5 Vi=1m/s +Juliix5
The continuity of flow equation is fundamental to much of the fluid flow in building services systems illustrate the continuity system and its associated equations.
39
The below results are for cooling tower expirement, energy balance :energy balance of the system, that is to say, the energy taken by the air must be equal to the energy supplied by the water flow. Question : Discuss the tabulated cooling tower results... Discuss in detail format!
PLEASE ANSWER IN A CLEAN AND COMPLETE MANNER. THANK YOU
To test the affordable pressure of the product, an engineer produced the below formula: P = 1²G¬1C=1 Where I is the surface energy intensity per unit time, G is measured in J/m2s and c is the speed of the production line in m/s. 1. Verify the validity of the equation. 2. If the applied energy is 0.01 J and the speed is 5.7m/s, t is 0.01 sec and A =0.117 inch2 calculate P, I, and G. 3. Using the above formula, produce a formula relating P to E (energy). Discuss the new relation and how it varies with its parameters.