QUESTION 5: Consider the ideal inverting summing amplifier in Figure 9.14(a).Design an ideal inverting summing amplifier to produce an output voltage of vo= -2.5(1.2v₁ +2v12 +0.25v13) assuming the largest resistance in the circuit is 409ΚΩ.Format: 59.409378229784R₁ (kn)R₂ (kQ)R3 (kQ)Format: 49.289Format : 706RF (KQ)Format: 768.763unvoUR 12U13wwww14wwwRF0R₁v₁ = 0R₂R3Figure 9.14(a)

We need to find out unknown resistance value for given output expression.

QUESTION 5: Consider the ideal inverting summing amplifier in Figure 9.14(a). Design an ideal inverting summing amplifier to produce an output voltage of vo= -2.5(1.2v1 +212 +0.25v73) assuming the largest resistance in the circuit is 409 ΚΩ. Format: 59.409378229784 R₁ (kn) R₂ (kn) Format: 49.289 R3 (kn) Format: 706 RF (Kn) Format: 768.763 0 ww R₁ 12- Unw v₁ = 0 Vo R₂ U13 WW R₂ Figure 9.14(a) ww RE

QUESTION 5: Consider the ideal inverting summing amplifier in Figure 9.14(a). Design an ideal inverting summing amplifier to produce an output voltage of vo= -2.5(1.2v1 +212 +0.25v73) assuming the largest resistance in the circuit is 409 ΚΩ. Format: 59.409378229784 R₁ (kn) R₂ (kn) Format: 49.289 R3 (kn) Format: 706 RF (Kn) Format: 768.763 0 ww R₁ 12- Unw v₁ = 0 Vo R₂ U13 WW R₂ Figure 9.14(a) ww RE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. Design a clipper circuit which limits input signals to +3V and -2V. This means that the output signal should not rise above 3V and should not fall below -2V. Assume Vs has amplitude of 5V and a frequency of 1 kHz, Verify your design by computer simulation on a computer.
For the given op-amp circuit, determine: (a) iout/iin2, (b) iin2/iin, (c) iin/Is, and (d) iout/Is.
A appropriate op-amp circuit with a gain of +100 is required for the ultrasonic device. Create a two-stage non-inverting op-amp circuit with Av = 10 for each stage. Provide calculation procedures that complement the circuit design.
- V2 15Vdo 3 U1A R1 2 1k V- LM324 1k V3 15Vde | VOFF = 0 VAMPL = 1 FREQ = 2k AC = 0 0. R2 Figure 4. Operational amplifier circuit. What frequency does the output voltage (across R3) have? What is the amplitude of the output voltage? From the output waveform and the input waveform, determine the gain of the op-amp circuit. Does this match with what you predicted? How could you change this circuit so that the output voltage would be nearly the same as the input voltage? What purpose would that serve? Can you modify the existing circuit and verify this experimentally? What is the phase difference between the output and input voltage? Derive the transfer function for the output-input relationship for the operational amplifier. How would the gain and the output change if a capacitor were in the feedback path instead of a resistor? (Examine the circuit using phasors and impedance and circuit analysis techniques). -w-
3ZF The typical value of the out impedance of an op-amp is a.between 100 Ohms to little less than 1 KOhms b.less than 100 Ohms c.at least 10 percent of the input impedance d.equivalent to short circuit
Problem C It is desired to have a gain of 20 for frequencies up to 180 kHz. Determine the minimum unity gain frequency specification for the op amp. The gain should be within at least 98% Vsig Rin + Rf Vcc/-Vcc +12v/ -12V Vout
What configuration of the op amp is used to couple one stage of a circuit to another by its input and output impedance characteristics?
Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using “Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = k Ohms
circuits 35 36
(Q1) Design a circuit with Op-Amp when Vi 3v and Vo = 12v (i) Using Inverting Amplifier (ii) Using Non-Inverting Amplifier Assume any value if necessary.
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)
9. The transfer function of an inverting amplifier with a short circuit feedback is -1 b--Rin Rin Where Rin is the input resistance of the op- amp. a- c- zero b-three 11. A system with two resistors, one capcitor and two inductors its number of states is a- two d- -1 c- four d- five