Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using "Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. 9 Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = _k Ohms

Design a voltage follower amplifier circuit with a voltage divider on it. Assume that you have 60v voltage input voltage with a frequency of 60hz. Instead of using "Universal Op Amp 2" as a component, use the OPO7 Amplifier. What should be the values of your R1 and R2 to get a reading of a voltage output equal to 5.38 volts at exactly 20ms. The arrangement of your input should be, the one that is at the top most is the Voltage Input followed by the R1 and the lowest part is the R2. 9 Draft17 Cursor 1 V(n005) Horz: 20.0054ms Vert: 5.3827036V What is the value of R2 in kilo ohms? No need to include the Units. R2 = _k Ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An op-amp circuit has the following values: +V = 11V, -V = -11V, Av = 113. Assume that the load will not restrict the output voltage swing. The maximum allowable value for Vin in mV is ?
For a given op amp, CMRR = differential gain = 108. What is the common mode gain of Op-Amp. A B C 1 10 100 107 and D 0.1
3K Calculate the the input Voltage of an inverting op-amp with the following parameters Rf = 1 MOhms, Ri = 20kOhms and Vo = 2V. a.3.47 mV b.-40 mV c.-3.47 mV d.40 mV
6) i need fast please now
3ZF The typical value of the out impedance of an op-amp is a.between 100 Ohms to little less than 1 KOhms b.less than 100 Ohms c.at least 10 percent of the input impedance d.equivalent to short circuit
An op-amp has a maximum output voltage swing between ± 14 V. The feedback resistors are R1 = 1.5 KQ, R2 = 7.3 k2, and R3 = 7.6 k0. The input voltage (Vin) is Vin = 0.2 V. What is the output voltage (Vout) to within 1% accuracy? o + Vin Vout= M r₁ ww + HI r3 V 0 + Vout Report questi
If Vi = 0.6v, calculate the output voltage Vo and the current through the feedback resistor. 25 kQ Rf 20 kQ V1 R1 Ор-amp V.
3R The op-amp will only slightly amplify signals: a.when the supply voltages are less than +/- 25V b.that are common on both the inputs c.that are different on both the inputs d.when the supply voltages are more than +/- 25V
Write a formula forVout (b) Non-inverting dc amplifier
An op-amp has an open-loop gain of 105 and an open-loop upper cutoff frequency of 10 Hz. If this op- amp is connected as an amplifier with a closed-loop gain of 100, then the new upper cutoff frequency is
In OP-AMP, signal applied to the inverting input gets amplified and obtained as the inverted signal at the output.
I need the answer as soon as possible