QUESTION 5:Assume the hosts and routers use classless IPv4 addressing scheme. Routing Table forRouter_ABC is given below.MaskNetwork AddressNext HopInterface/28200.100.110.112fa0/0/26200.100.110.64fa0/1/24200.100.101.0fa0/2AnyAny100.150.50.200fa0/3Show the steps involved in forwarding process if a packet arrives at Router_ABCwith the destination address 200.100.110.70

Answered: Image /qna-images/answer/ae141c67-9d51-4909-9c38-a97af9773932.jpg

QUESTION 5: Assume the hosts and routers use classless IPv4 addressing scheme. Routing Table for Router ABC is given below. Mask Network Address Next Hop Interface /28 200.100.110.112 fa0/0 126 200.100.110.64 fa0/1 /24 200.100.101.0 fa0/2 Any Any 100.150.50.200 fa0/3 Show the steps involved in forwarding process if a packet arrives at Router_ABC with the destination address 200.100.110.70

QUESTION 5: Assume the hosts and routers use classless IPv4 addressing scheme. Routing Table for Router ABC is given below. Mask Network Address Next Hop Interface /28 200.100.110.112 fa0/0 126 200.100.110.64 fa0/1 /24 200.100.101.0 fa0/2 Any Any 100.150.50.200 fa0/3 Show the steps involved in forwarding process if a packet arrives at Router_ABC with the destination address 200.100.110.70

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Consider the following situation: Source node has packets number 1, 2, 3, 4, 5, 6, 7, and 8 to send to the destination Source starts transmitting and packet 3 is lost on its way to its destination. The rest of ACK and data packets arrive successfully Window size is 5 packets ACKs are packet number-based. Draw a diagram that illustrates what happens in the network during sender’s transmission of packets 1 – 8 when Go-Back-N protocol is used and a diagram that illustrates what happens when Selective Repeat is used. Initial diagrams have been already drawn for you. You need to complete the drawing.
A simple CIDR routing table is shown in Figure 1. For each of the destination IP addresses below, indicate which entry in the table it matches. Indicating none if no routing entry can be matched (hint: given an IP packet, the router will check whether there is a routing entry which can be used to route this packet, by checking the destination IP address in the packet with each routing entry: based on the subnet mask of each routing entry, it can extract the network ID and compare it with each routing entry; if there are a few routing entries which can match, the entry with the longest subnet mask wins). Address Mask Output Port 10.19.0.0/16 1 10.19.128/17 2 10.19.192/18 3 10.19.192/19 4 0.0.0.0/1 5 141.219.2.10 10.10.10.10 10.19.86.141 10.19.193.6 10.19.255.86 10.19.192.18
There is a routing table in the figure on a router. If packets with the following destination IP addresses arrive at the router, where are they routed? a) 198.52.61.10b) 198.53.40.201c) 198.52.60.89d) 198.52.63.113 Show your work and reasoning for each option.
q18- When the destination network is not listed in the routing table of a Cisco router, what is possible action that the router might take? Select one: A. The router forwards the packet to the interface indicated by the source address. B. The router forwards the packet toward the next hop indicated in the ARP table. C. The router discards the packet. D. The router sends an ARP request to determine the required next hop address.
Total latency is equal to a summation of network delay contributors such as frame transmission time, queuing time, and propagation time. Use the assumptions listed below to answer the questions below. Assumptions: • Host A and Host B are connected to a network. Packets sent from Host A to Host B transit through two Routers, R1 and R2 (Host A ? Router 1? Router 2 -? Host B) • The links that connect the hosts and routers are Ethernet 1000B and are short distance and can be ignored in any further delay calculations • The link between the two routers is 8km long and are connected by a T-1 WAN link (line rate = 1.544Mbps) • a single packet (size = 1500bytes) is routed from Host A to Host B through the network. The two routers, R1 and R2, introduce queuing delay of 3 msec and 5 msec, respectively. • Assume the signal propagation velocity in the T-1 channel = Vp = 2 x 108 m/sec a. Calculate the latency (in msec) required to send the 1500byte packet from Host A to Host B
A IPV6 global unicast address is composed of a Global Routing prefix = 2001:0540:FACE, Subnet ID = 0020, and an interface id = 0000:0000:0000:0040. Assuming the IPV6 global unicast address follows the "3+1+4" Rule, which of the following is the correct IPV6 global unicast address representation? %3D %3D 2001:540:FACE:20:40/32 2001:540:FACE:20:40/64 2001:540:FACE::40:20/32 2001:540:FACE::40:20/64
14 The following figure shows a TCP transaction. Assume Host A always has data to send, and each packet has size 20 Bytes. Assume Host A has a sending window of 40 Bytes, that is, it can send two "in-flight” packets maximum. Answer the following questions. A. At the time marked "1", i.e., when the first packet times out, will Host A send any packet? if your answer is no, explain why not; if your answer is yes, how many packets will be sent, what are the sequence numbers of them? B. At the time marked "2", i.e., when the ACK of the 2nd packet is received by Host A, will Host A send any packet? if your answer is no, explain why not; if your answer is yes, how many packets will be sent, what are the sequence numbers of them? Host A Host B Seq=80, 20 bytes of data Seq=100, 20 bytes of data Xª 1 2- timeout
List all the static routes on each of the 4 routers required for full communication across the topology. The addresses with question marks have been relabeled. I think each router should have 3 static routes. This is using the ip route command (ip route <netid> <net mask> <next hop>)
1. What is the difference between packet fragmentation (i.e., at network layer) and frame frag- mentation (i.e., at link layer) in terms of purpose? 2. Suppose that host A is connected to a router R1, R1 is connected to another router, R2, and R2 is connected to host B. Suppose that a TCP message that contains 800 bytes of data and 20 bytes of TCP header is passed to the IP function at host A for delivery to B. Show the Total length, DF, MF, and Fragment offset fields of the IP header in each packet transmitted over the three links. (Assume that link A-R1 can support a maximum frame size of 1024 bytes including a 14-byte frame header, link R1-R2 can support a maximum frame size of 512 bytes, including an 8-byte frame header, and link R2-B can support a maximum frame size of 432 bytes including a 12-byte frame header.) (*hint: the Fragment offset field is denominated by 8-bytes, not bytes) 3. What is the purpose of the path MTU discovery process (see textbook Figure 5-42) and why does…
The first portion of IPv4 header of an FTP datagram packet is shown below. Offset 0 4 Header Data 0x48007000 OxA0120000 If the datagram was received by a router that is connected to a network with maximum transmit unit (MTU) = 0x3000. Show the headers of the resulting fragments transmitted by the router. Hint: 1) The first few fragments will have total length = MTU. 2) Fragmentation offset refers to datagram payload, not the fragment Fragmento Offset Header Data 0 4 Offset 0 4 Fragment1 Header Data Blank # 1 Fragment2 Offset Header Data 0 4 Blank1 Blank2 Blank # 3 Blank # 4 Blank # 2 Blank # 5 Blank3 Blank4 Blank # 6 Blank5 Blank6 N A A/ A/
Computer Science In Python, I am trying to make a client and server code that passes the payload with the requirements. The client has to specify the length of the data packet, up to max, specify how many times to pass the data packet, and specify the server IPv4 address. Both the client and the server need timer functions and compute the time needed to perform the number of sends both the Client and the server need to display the local and remote IPv4 addresses, total time, and bytes per second. Please help, Thanks.
Consider a router that interconnects three subnets: Subnet 1, Subnet 2, and Subnet 3. Suppose all of the interfaces in each of these three subnets are required to have the prefix 223.10.128/24. Also suppose that Subnet 1 is required to support at least 50 interfaces, Subnet 2 is to support at least 100 interfaces, and Subnet 3 is to support at least 12 interfaces. Provide three network addresses (of the form a.b.c.d/x) that satisfy these constraints.