QUESTION 5(a)A PMMC instrument with a f.s.d of 10pA and Rm = 10002 to be employed as avoltmeter with range of 10V, 50V and 100V. Calculate the required values ofmultiplier resistors for the circuits of Figure 5(a)-i and Figure Q5(a.ii).R3R3R1R,R R.50V10V10V50V100V100V(i)(ii)Figure Q5(a)(b)Two voltmeter are used to measure the voltage across the 50kn resistor in the circuitshown in Figure QS(b), Meter A has ac sensitivity of 10K2V, a guaranteed accuracyof 97% at full scale, and is set on its 200V range. Meter B has an ac sensitivity of4KNV, a guaranteed accuracy of 98% at full scale and is set on its 100V range. Whichmeter will provide a more accurate result?10kR1R 15kV- 120VrmsRy 50kFigure Q5(b)

QUESTION 5 (a) A PMMC instrument with a f.s.d of 10µA and Rm = 10002 to be employed as a voltmeter with range of 10V, 50V and 100V. Calculate the required values of multiplier resistors for the circuits of Figure 5(a)-i and Figure Q5(a.ii). Ry R1 R S0V 10v 10V 50V 100V 100V (i) (ii) Figure Q5(a) (b) Two voltmeter are used to measure the voltage across the 50k2 resistor in the circuit shown in Figure QS(b). Meter A has ac sensitivity of 10k2V, a guaranteed accuracy of 97% at full scale, and is set on its 200V range. Meter B has an ac sensitivity of 4k2V, a guaranteed accuracy of 98% at full scale and is set on its 100V range. Which meter will provide a more accurate result?

QUESTION 5 (a) A PMMC instrument with a f.s.d of 10µA and Rm = 10002 to be employed as a voltmeter with range of 10V, 50V and 100V. Calculate the required values of multiplier resistors for the circuits of Figure 5(a)-i and Figure Q5(a.ii). Ry R1 R S0V 10v 10V 50V 100V 100V (i) (ii) Figure Q5(a) (b) Two voltmeter are used to measure the voltage across the 50k2 resistor in the circuit shown in Figure QS(b). Meter A has ac sensitivity of 10k2V, a guaranteed accuracy of 97% at full scale, and is set on its 200V range. Meter B has an ac sensitivity of 4k2V, a guaranteed accuracy of 98% at full scale and is set on its 100V range. Which meter will provide a more accurate result?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3/ Consider the circuit in Figure (2), answer (a)-What type of circuit is this? (b)-What is the total peak secondary voltage? (c)-Find the peak voltage across each half of the secondary. (d)-Sketch the voltage waveform across RL. 120 Vrms 4:1 00000 elile D₁ D₂2 Figure (2) WWII RL 1.0 ΚΩ
Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the current wave form through the SCR for the input values of 5 V(45°), and 10 V(90°), and 8 V(135°). 4 Vin RL 2.2k2 10 V R1 - - - 8 V - A $20KQ 5V Vin D DO 45° 90° 135° 2N3870 R2 2kO Figure 3
i need the answer quickly
Please i need the answer for this question about Electronics i have an exam now quickly please with clear write hand and answer thanks
H.W: Determine Vo and ID for the circuit in figure below after adding a resistance of 2kQ in series with both diodes +20 V Si St 4.7 ks2
for the circuit shown below: The lower reference threshold 10v vin 5 simwt 02.5 O-2.5 O2.4 O-2.4 -10v 3 kOhm 1 k Ohm
- 8V R₁ = 1.2k √√ flav R2=2.5K2 O un R3-5602 Analyze the circuit using any circuit an : analysis method to compute for the Diode Current (10). Diode Voltage (vo), Lood Voltage (Vc). Indicate the method used and support the solution with explanations. Enclose the computed values in a box. thank you. A Vo
Exam: Find the output waveform for the following full wave rectifier and the current pass through R1? D Vpi= 0.7v 1:4 R= 10kn ww D2 Vp=0.7v
Based on electric circuit shown in Figure 2. Determine whether the LED 1 and LED 2 is “ON" or "OFF" for V1 = 2V and V1 = 3.5V if for both LEDS are silicon LED. Explain the answer given. V1 OUT R1 OPAMP 100kN V2 LED 1 LED 2 4Vdc R2 500kn Figure 2: Op-Amp circuit with LED
With calculation, determine what is the input voltage, Vin (+Ve cycle) when the Zener diode D5 starts to conduct current? Show the calculations.
Semiconductor devices in power electronics are O Diode, Transistor, Thyristor and IC O Diode, Resistor, Thyristor and IC O Diode, Inductance,Thyristor and IC O Diode, Transistor, Thyristor and resistor
I need the answer quickly