Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cycle k is 0.5. The load is resistive with R-10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch-1V. The input power and the conduction losses in the switch are respectively equal to: Select one: a. 1272 W and 7.95W O b. 1264 W and 11.24W Oc. 1124 W and 11.24W Od. None of these

Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs 160 V. The switching period is 0.25 ms and the duty cycle k is 0.5. The load is resistive with R-10 OHMS. When the switch is ON, a voltage drop across the switch is noted of Vch-1V. The input power and the conduction losses in the switch are respectively equal to: Select one: a. 1272 W and 7.95W O b. 1264 W and 11.24W Oc. 1124 W and 11.24W Od. None of these

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ZEV * OMANTEL I. A moodle1.du.edu.om Question 2 Not yet answered Marked out of 2.00 P Flag question A buck converter produces an output voltage of 100 V across a 100 Ohm load resistor. The output voltage ripple is 0.5 %. The output current ripple is 2 A. The dc supply is 200 V. The switching frequency is 1 kHz. The value of the inductor is: Select one: O a. 25.00 milli Henry b. 35.25 micro Henry O c. None of the above d. 88.55 micro Henry O e. 75.15 nano Henry Previous page Next page
Draw circuit for Boost Converter. Also derive its Output equation. What will be the value of Duty Cycle (D) if the input voltage is 50 V DC and desired output voltage is 20 V DC.
The single-phase wave rectifier is used to charge a 200 V battery with an internal resistance of 0.2 as shown in the figure. SCRs are triggered by a steady dc signal. If SCR2 is made open circuit, what will be the average charge current?
In the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to-peak ripple in the output voltage
is Idc -Idc 0 K de 27 If ripple-free load current in steady-state is assumed, the input current is waveform of the single-phase full-wave rectifier may then be depicted as shown in the figure above for an ideal input transformer. With the assumption that the supply is ideal and perfectly smooth and ripple free load current, which implies an infinitely large load inductance, it is quite straightforward to obtain an analytical expression for the input current harmonics. The rectangular wave is defined as when 0
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
1. For the above Boost converter, what is the duty cycle? a. 0.95 b.0.75 c. 0.25 d. None of the obove 2. For the above Boost converter, what are the average current flowing in the MOSFET and diode? a. 12A, 4A b. 12A, 12A c. 4A, 4A d. 16A, 4A 3. For the above Boost converter, what is the peak switching current flow in the MOSFET and diode? a. 19.75A, 19.75A b. 15.75A, 15.75A C. 19.75A, 15.75A d. None of this 4. what is the max voltage stress on the MOSFET and diode? a. 10V, 10V b. 10V, 40V c. 40V 40V, d. none of this 5. what is the output voltage peak to peak ripple? a. 0.3V b. 0.1V c. 0.6V d. none of the above
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) What should the inductance value be for the circuit to always operate in Continuous Current Mode (CCM)? Calculate.
Derive the average and rms values of output voltages and currents for three phase semi converter. Power Electronics
A buck converter is working in a steady state. The output voltage and the inductor current can be assumed to be ripple-free, The inductor voltage v during Ton is 50V and during Toff is 3OV. Assuming all devices are idea then: What is the input voltage? Answer: 70
Design a boost converter to provide an output voltage of 36V from a 24 V source. The load is 50 W. The voltage ripple factor must be less than 0.5%. Specify the duty cycle ratio, switching frequency, inductor and capacitor size, and power device.
Example 3:-