Question 4 The phase currents in a delta-connected three-phase load are as follows: between the red and yellow lines, 30 A at p.f. 0.707 leading; between the yellow and blue lines, 20 A at unity p.f.; between the blue and red lines, 25 A at p.f. 0.866 lagging. Calculate the line currents. Round your currents to one decimal place and your phase-angles to the nearest whole number.

Question 4 The phase currents in a delta-connected three-phase load are as follows: between the red and yellow lines, 30 A at p.f. 0.707 leading; between the yellow and blue lines, 20 A at unity p.f.; between the blue and red lines, 25 A at p.f. 0.866 lagging. Calculate the line currents. Round your currents to one decimal place and your phase-angles to the nearest whole number.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
in three phase it has been found that a negative sequence and zero sequence are absent what do you conclude from it?
3. Find the line currents and the real power absorbed by the load. Caution: There is no neutral wire provided in the figure. Ia 120/0° rms gj5Q Ω 120-120° rms Ib b B 120/120⁰ rms с n Ic 10 Ω -j10 Q2 C
Sum of scattering angles in Laboratory coordinate system is always equal to * O 2n None of them О п/2
Compute the admittance in millisiemens if R = 19 ohmsXL = 10 ohmsXC = 21 ohms State the phase relation for current & voltage in the circuit. Answer this way: I ( leads / lags / is in phase with ) E by angle° Example Answer: I leads E by 1.2345°
In a balanced tephasic system Y - Delta of the figure. Find the line current IL and the average and supplied power to the load
2. Determine the Ripple factor, Kr VA wt 2 2
Find out the zero-phase sequence components of the following set of three unbalanced voltage vectors: Va =10cis30° ,Vb= 30cis-60°, Vc=15cis145°" (THOS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE THE LETTER WITH THE CORRECT ANSWER AND PLEASE PROVIDE YOUR CLEAR SOLUTION! A 16.809cis-72.579° B 5.603cis72.579° C 16.809cis-47.421° D 5.603cis-47.421°
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 j3n Za j20 ZA j30 j3n -j20 j 30 -j20 Zo -j20 ZE j30 -j2n j 3n. ZF Assume the generator is star-connected with neutral, calculate total system power, total power factor, and current in neutral.
Consider the network given in figure below, where the numbers indicate admittances per unit. Find the admittance matrix 1 1- j2 2 - j3 1- j2 2 - j6 3. 3- j4 1- j4
Q4 a) A three-phase system has a rms phase voltage of 6.3 kV. What is the line voltage?
2. For the following system shown in the figure, calculate: a. The current through each phase of the load. b. The total real and reactive power of the three-phase load. c. The power factor at the load side. A 220 V 20° 220VL-120° U8 vol 152 I 220 VI20° 9. M.