Question 4 A shaft of 75 mm diameter fails (experiences the onset of yield) under a bending moment of 2.5 kNm. A similar shaft is exposed to a direct bending moment of 1.5 kNm, a torsional load of 0.75 kNm and a direct load (F) of undetermined magnitude. Use the Tresca Criterion to determine the maximum direct load the second shaft can carry before failure (onset of yield).

Question 4 A shaft of 75 mm diameter fails (experiences the onset of yield) under a bending moment of 2.5 kNm. A similar shaft is exposed to a direct bending moment of 1.5 kNm, a torsional load of 0.75 kNm and a direct load (F) of undetermined magnitude. Use the Tresca Criterion to determine the maximum direct load the second shaft can carry before failure (onset of yield).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A beam has fluctuating bending moment and is not rotating. The bending moment has a maximum of 1kNm and a minimum of 100kNm. The beam is made of AISI1020CD steel with a square cross section. There are no stress concentrations. a. Determine the fully corrected endurance limit as a function of the cross section (cross section unknown) b. Determine the required size for a factor of safety of 2 using the Gerber Fatigue Failure Theory
NEED IN RUSH THANKS
A 50 mm diameter circular bar is used as a simply supported beam 10 m long, is simply supported at the left- hand end and at its mid- point. it carries a uniformly distributed load of 48 KN/m between the supports and a point load of 50 KN at the right- hand end. Determine : (a) draw shear force and moment diagrams. ( b) flexural * .stress
Provide clear/complete solution and diagram for this problem. A 10 m length shaft is used to transmit 50 kw power at 450 rpm. If the shaft stress is limited to 40 Mpa, find the angular deflection of the steel shaft. A. 4.23o B. 8.340 C. 7.23o D. 11.27o
Need complete solution please. Tysm
Problem 2. A 300-mm diameter solid disk is to be used as a flywheel in a machine to reduce speed fluctuations. If the disk material has yield strength S Y =720 MPa, density p=7000 kg/m^ 3 . and Poisson's ratio J = 0.2 ^ c , find the maximum allowable rotational speed (in rpm) for a safety factor of 1. a) Solve using the MSST. b) Solve assuming that the disk is mad of cast iron having Sut = 207MPa , Fuc = 780MPa, p = 7000 kg/m³, and Poisson's ratio v r = 0.26 , Use Coulomb-Mohr theory.
A bar AISI 1035 steel forged and heat treated with minimum yield strength of 570MPa is subjected to bending moment of 290Nm and a torsional moment of 310Nm. Assuming a factor of safety of 2, determine the diameter of rod using the following theories of failure (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory, also specify which diameter is considered as safe
A steel bar withstands simultaneously a 30 kN compressive force, a 5 kNm bending moment and a lkNm torque. Assume the cross-section is circular with diameter R. Determine, for a point at the position of greatest compressive bending stress: (a) The normal stress on a plane inclined at 30° to the shaft axis (b) The shear stress on a plane inclined at 60° to the shaft axis
Q8
None
Which set of compatibility equations matches the following torsion members connected end-to-end in series? 30 in. O || = C a 560 8₁ a & + gap 05/0 18 in. 6 in. (2) 0 & + ₂ = 0 О ф, = фг 0 8₁ = 8₂ - 8₂ 04+₂=0 & + ₂ = constant Ta (3) 8₁ + gap = 8₂ &₁ = & + gap D. & + ₂ = constant 8 in. (2)
Four-wheel drive Jeep Cherokee 4L AMC 242 pulls a heavy load up the hill at speed v. Power is evenly distributed over all wheels. a) Calculate the torque on the shafts A, B and C. b) Calculate the shear stress τ and the safety factor nτ with respect to the yield on the axes A, B and C. c) Calculate the deflection θ on the axes A, B and CStarting values: ReL = 700 MPa E = 200 GPa ν = 0.3 P = 91 kW v = 50,4 km/h Drive shaft = 1.31 ”Drive shaft = 1.12” Drive shaft = 0.96 ” The first three numbers in a typical size (225/45R17) are the tire's indicated section width in millimeters, measured from sidewall to sidewall. The second pair of numbers (225/45R17) is the tire's aspect ratio. This percentage represents the ratio of sidewall’s section height to the tire’s section width. The section height can be calculated by multiplying the section width by the aspect ratio percentage. For example: 225mm x 0.45 = 101.3mm The last number (225/45R17) is the diameter of the wheel in inches. For example:…