2m 1.5 m 0.5 m 0.5 m 56m y A a.) A 1.5 m length of 30mm diameter solid steel bar fixed at one end is subjected to a maximum bending moment of 500Nm. What additional torque can be applied to the bar before the material will start to yield according to the Von Mises criteria if the yield strength of the steel is 350MPa?

2m 1.5 m 0.5 m 0.5 m 56m y A a.) A 1.5 m length of 30mm diameter solid steel bar fixed at one end is subjected to a maximum bending moment of 500Nm. What additional torque can be applied to the bar before the material will start to yield according to the Von Mises criteria if the yield strength of the steel is 350MPa?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. A cylindrical bar of steel with a diameter of 10 mm is deformed elastically by applying a force along the bar axis. Determine the force that produces an elastic reduction in diameter of 3 X 10-³ mm. You may use material properties given in Table 6.1 below. Table 6.1 Room-Temperature Elastic and Shear Moduli and Poisson's Ratio for Various Metal Alloys Metal Alloy Aluminum Brass Copper Magnesium Nickel Steel Titanium Tungsten GPa 69 97 110 45 207 207 107 407 Modulus of Elasticity 10 psi 10 14 16 6.5 30 30 15.5 59 Shear Modulus GPa 25 37 46 17 76 83 45 160 10° psi 3.6 5.4 6.7 2.5 11.0 12.0 6.5 23.2 Poisson's Ratio 0.33 0.34 0.34 0.29 0.31 0.30 0.34 0.28
The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be expressed by the equation t = (kz²/³) N-m/m, where z is in meters. A torque of T-50 N-m is applied to the bolt head. Assume the shank has a constant radius of 7 mm. The shear modulus of elasticity for A-36 steel is 75 CPa. (Figure 1) 50 -7-50 Nm Determine the constant k. Determine the amount of twist in the 50-mm length of the shank
QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a cross-sectional area of 40x40 mm and a wall thickness of 4 mm, is subjected to an axial tensile load of "6" KN from both ends. remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate %3D %3D the final length of the rod under this tensile load in "mm".
Please solve this question carefully and circle the final answer with the correct units use the image below
Please full solution with big and clear handwriting
answers stated in box are incorrect
35 mm 10 kN-m 2.36 x106 mm 70 GPa %3D %3D (1) C2 40 mm (2) 4.02 x106 mm %3D B 2800 mm 45 GPa C 3600 mm A composite torsion member consists of two solid shafts joined at flange B. Shafts (1) and (2) are attached to rigid supports at A and C, respectively. T1 kN-m A concentrated torque T is applied to flange B in the T2 kN-m direction shown. Determine the internal torques and MPа shear stresses in each shaft. Also, determine the rotation angle of flange B. MPa ((Use the sign convention detailed in the fourth scene of this movie for internal torques and rotation angles.) PB rad 1st 2nd 3rd Enter Shaft properties I| ||||
5. A straight steel rod of circular cross-section and length 72 cm rotates about an axis through one end perpendicular to its length. Calculate the speed of rotation that will produce a maximum tensile stress of 55.85 MPa in the rod and the elongation of the rod at this speed. The specific weight of steel is 7833.413 kg/m³ and Young's modulus is 16.67 x 10¹0 N/m². [Ans. 2190 rpm, 0.018 cm]
For this please explain the equation you formed ie sigma(2.5-x)/E + sigma b * x /E ...please explain how you formed this equation .
Q4/ Answer one of A) A cylindrical rod of 16 mm diameter is made of plain carbon steel. It is subjected to axial load of 5000 N, a steady torque of 50 N-m and bending moment of 75 N-m. Using the theories of failure to calculate:- 1) The factor of safety available. Assume yield strength as 400 MPa for plain carbon steel. And then comment on the result you get. 2) The maximum yield strength of shaft material would be necessary using factor of safety of 1.686.
A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length having an external diameter of 16mm and a wall thickness of 3mm. The rod and tube are rigidly connected at their ends so that they twist together when a torque of 20 Nm is applied. Galuminum = 30GPa; Gbrass = 40GPa. Determine: a) The values of the torsional stiffness for the rod and the tube b) The torque transmitted by each c) The maximum shear stress in each d) The angle of twist
A 4-cm-OD, 3-cm-ID, circular shaft supports a 200 N load and is supported at two points, which are 2-m apart as shown here. What is the radius of curvature of the bending shaft when it is made of a material whose modulus of elasticity is 50 GPa? Multiple Choice O O O O 1087 m 5 m 432 m 65 m