QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a cross-sectional area of 40x40 mm and a wall thickness of 4 mm, is subjected to an axial tensile load of "6" KN from both ends. remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate %3D the final length of the rod under this tensile load in "mm".

QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a cross-sectional area of 40x40 mm and a wall thickness of 4 mm, is subjected to an axial tensile load of "6" KN from both ends. remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate %3D the final length of the rod under this tensile load in "mm".

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Related questions

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: E=PA∆LL⇒EA∆LL=P

Q: Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and…

Q: A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness…

A: Given data for aluminum cylinder 2014-T4

Q: A long, flat steel bar 260mm wide and 35mm thick has a circular hole 50mm in diameter, centrally…

Q: 3. A circular bar rigidly fixed at its both ends is 1.2 m long. It uniformly tapers from 100 mm at…

A: Given data: L=1.2 md1=100 mmd2=75 mm∆T=25 KE=200 GPaα=12×10-6 /K Need to determine the stress…

Q: A hollow circular column of internal diameter 20 mm and external diameter 40 mm has a total length…

A: giveninternal diameter of column d=20mmexternal diameter D=40mmtotal length L=5mE=2×105N/mm2yeild…

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The…

Q: A wedge shaped bar, as shown below, is subjected to a tensile load, P. The width of the root and tip…

A: To Find : The mean average of area of each element. Given : The lenght of bar is L=15 cm The…

Q: d 5 in 150 mm 3 in W 2 in 40 mm 1.25 in F 600 lbf 2 kN 250 lbf M Ste Ste C

Q: 1. (Problem 4.192 from the text book) Two vertical forces are applied to a beam of the cross section…

Q: 1. A steel bar is 50 mm in diameter and 2000 mm long. It is surrounded by a shell of cast iron 5 mm…

A: Given Diameter, d = 50 mm Length, L = 2000 mm Thickness, t = 0.9 mm Find Load, P

Q: A steel bolt and sleeve assembly are shown in the figure. The nut is tightened up on the tube…

Question

Transcribed Image Text:QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a cross-sectional area of 40x40 mm and a wall thickness of 4 mm, is subjected to an axial tensile load of "6" KN from both ends. remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate %3D %3D the final length of the rod under this tensile load in "mm".

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a tensile force P (see figure). If the bar elongates by 0.0)95 in., what is the decrease in diameter
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?