Question 4 (1 point) L (ft) w (k/ft) Alimit= L/300 Sy = 36ksi Steel For a W21x50 W-section beam with w= 2.9 k/ft and L= 10.5 ft, report the maximum shear experienced by the beam, Vmax, in kips. Do not include units in answer, include at least 3 significant digits.

Question 4 (1 point) L (ft) w (k/ft) Alimit= L/300 Sy = 36ksi Steel For a W21x50 W-section beam with w= 2.9 k/ft and L= 10.5 ft, report the maximum shear experienced by the beam, Vmax, in kips. Do not include units in answer, include at least 3 significant digits.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

See the image below. A hot-rolled l-beam section has yield strength fy = 300 MPa, ultimate strength fu = 320 MPa. b = 158 mm, t = 10 mm, H = 266 mm, tw = 13 mm. Calculate the nominal shear capacity of this section (in kN, round to whole number). b I H tw H
Hand written please
0:0£ IO %or M M E a ".ull zain IQ docs.google.com/forms O Q2: For the cantilever beam with uniformly distributed load shown in Figure 2. Use the data (bf,hf,bw,hw) from Table 2, determine the following: 16KN/m Sm bf hf hw hf bw Figure 2 1. The maximum shear force in the beam in (kN) Your answer ...
A structural engineer has drawn the shear force diagram (SFD) for a beam as shown in figure below. He assumed the sign convention for shear force as downward force acting on the right of the section as positive and vice versa. All the loads acting on beam are vertically downwards. No couple is acting on any part of the beam. 17.408 kN 5 kN +ve SFD Parabola A O kN B D. OkN E -Ve SFD ve SFD 8.26 kN 10.792 kN 1.5 m 1m 6 m 2m a) Locate the position of supports on the beam. Identify the type of the beam. b) What type of loads are acting on the beam? Calculate the magnitude and position or extent (length of the beam) of the each load acting on the beam c) What are the magnitudes of support reactions?
Determine the nominal axial compressive strength, Pn for the following cases: a. L= 15 ft b. L = 20 ft Note: Pinned both end support W10 x 33 A992 steel r = 1.94 in E = 29000 ksi L Fy = 50ksi Note: Ag = 9.71 in^2
Q.1: By using LRFD method: A. Determine the max. load (P) can be applied on the structure shown in Figure, neglect block shear. B. Depends on channel section, find channel size (C9) that can be used as shown in Figure assume Pu=600 kips. 2PL(1*20)in 3*5in=15in dpoit P A36 for PL A572-Grade 50 for Channel 2C=?
A cantilever beam of length L = 6 ft supports a uniform load of intensity q = 200 lb/ft and a concentrated load P = 2500 lb. Calculate the required section modulus if the allowable stress is 15000 psi. Select a suitable wide flange beam from the table. W8X35 W8X28 W8X21 W8X15 Weight per foot lb 35 28 21 15 Area Depth 2 In² 10.3 8.25 6.16 4.44 in 8.12 8.06 8.28 8.11 in 0.310 0.285 0.250 0.245 9= 200 lb/ft Flange Web Thickness Width Thickness In 8.020 6.535 5.270 4.015 L=6 f in 0.495 0.465 0.40 0.315 P = 2500 lb I in4 127 98 75.3 48 I S in³ 31.2 24.3 18.2 11.8
Determine maximum shear and momentum of the beam load. Compute the value of the concentrated load. Using rule of thumb find initial size of beam Design a monolithic reinforced concrete Picture below for reference
Please explain all options..
For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimali. For the given beam on Problem 5.39 Page 220, calculate the Maximum Negative Shear in kips if the given 3kip/foot uniform load from the figure is replaced by 10.6kip/foot. Express your answer in 2 decimal places. Just input the magnitude of the shear force only, no need for the negative sign anymore.
A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm thickness as shown in the figure. There are twelve power driven rivets of 20 mm diameter at a pitch of 50 mm in both directions on either side of the plate. Two cover plates of 10 mm thickness are used. The capacity of the joint in tension considering bearing and shear only, with permissible bearing and shear stresses as 300 MPa and 100 MPa respectively is 50mm 50mm 50mm 3. %3D 50 mm 50 mm --6-0--0-- 50 mm A--A - A- -H--- e-- 50 mm --0- 11 9-
Helps*