Question 3: Please refer to the metal bar and its cross-section shown below. Two strain gages a and and b are attached to the bar as shown; note that 3 is the angle of their orientation with the x-axis. Assume: the Young's modulus of the metal = 16, 500 ksi; the Poisson's ratio of the metal = 0.33; P, = 13 kips; P, = 20 kips; d = 4.0 in.; t = 0.75 in.; L = 18 in.; and B = 40°. Determine the strains expected in the strain gages.

Question 3: Please refer to the metal bar and its cross-section shown below. Two strain gages a and and b are attached to the bar as shown; note that 3 is the angle of their orientation with the x-axis. Assume: the Young's modulus of the metal = 16, 500 ksi; the Poisson's ratio of the metal = 0.33; P, = 13 kips; P, = 20 kips; d = 4.0 in.; t = 0.75 in.; L = 18 in.; and B = 40°. Determine the strains expected in the strain gages.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.11P: The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y...

See similar textbooks

Related questions

Q: The state of strain at the point has components of €, = 180(10 6) €y = -100(10-6) and All attempts…

Q: 3. A force P is applied to the rigid lever arm ABC as shown. The arm rotates counterclockwise about…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the…

A: Normal stress is defined as the intensity of force exerted on the cross sectional area of a member.…

Q: A rectangular block has dimensions of 3 in, 4 in, and 5 in along the X-, y-, and z- axes,…

A: The Answer is below

Q: The steel railroad increases its length when exposed to heat from 70°F to 95°F. The coefficient of…

A: Given data T1=70°F and T2= 95°F Thermal expansion coefficient = 11.7 ×10-6 (m/m°C) Find the strain

Q: QUESTION 4: An originally rectangular rubber piece is deformed into the shape given by the dashed…

A: To find (a) The average normal strain along AC and BC. (b) The shear strain γxy along all the…

Q: when they are initially pinned to a straight, rigid, horizontal beam BF. Subsequentially, heating of…

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

Q: The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6.…

Q: Compound axial member ABC has a uniform diameter of d = 1.45 in. Segment (1) is an aluminum [E₁ =…

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Q: The strain rosette shown below was used to obtain normal strain data at a point on the free surface…

Q: Problem 2 refers to the following: a load P is applied to the cantilever beam shown which causes it…

A: (a) Draw the given diagram of the cantilever beam.

Q: A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this…

Q: Compound axial member ABC has a uniform diameter of d=1.45 in. Segment (1) is an aluminum…

A: Given, A compound axial member made of Aluminum and copper Diameter of the axial member, d=1.45 in.…

Q: Question-1: The strain rosette shown in the figure was used to obtain normal strain data at a point…

A: given;εa=550μεεb=-730μεεc=-375μεν=0.30

Q: A rectangular elastic plate ABCD is subjected to a biaxial loading of Oyx- 150 MPa and o-100 MPa.…

A: Given Stress in x direction = 150 MPa Stress in y direction = 100 MPa Young's modulus, E = 200…

Q: 6. Airplane components often have a “stressed skin" construction, which consists of a thin sheet of…

Q: A 2.0-m-long wire stretches 1.0 mm when subjected to a load. What is the tensile strain in the wire?…

A: GivenLength of wire L=2m∆L=1mm=1×10-3 m

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction and given data

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help me answer this thank you
Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and 2 cm in diameter. The combination is subjected to a tensile force of 5000 N. Find the strain in each rod. Young's Modulus of Steel use 20×10¹⁰ Pa, of brass use 10×10¹⁰ Pa. Find the elongation of each rod.
Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as -3800 μm/m. Use the dimensions L₁ = 1900 mm, L₂ = 1425.00 mm, a = 190 mm, b = 380 mm, and c=143 mm. Determine: (a) the normal strain in bar (1). (b) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin C before the load is applied. (c) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin B before the load is applied. L₁ Answer: (a) &₁ = (b) E₁ = A i i (c) E₁ = i 1 1 1 a B (1) b Rigid bar L2 με με με C (2)
The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to be ɛx = 139 x 106. The shear strain at point A is found to be yxY = R x 10° radians. The magnitude R is given by: (Take E= 204 GPa and Poisson's ratio =0.3). The cross-section of the beam is rectangular with depth 400mm and width 200mm respectively 100m 4ocmm 40om 600mnın 1000 mm 200mm
A 45° strain rosette was placed on the surface of a critical point on an engineering part. The following were measured: Ea = 400 μ C ли 45° mm mm 45° ли Gauge a was aligned with the x-axis. a. Determine Ex, Ey, Yxy b. Using Mohr's Circle, find the principal strains and the maximum shear strain at that point, and find the orientation of the principal planes from the given x-y axes. y ли & = 450 μ ஆ b a mm X mm & c = 500 μ y+ ос mm mm eb 10₂ X
The question is related to Modulus of rigidity and is attached as an image.
The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.
1. Find the relationships between strain components in the polar coordinate and strain components in the rectangular coordinate.
Please give me the solution, don't waste my question if you don't really knownthe solution. I will vote it up for you thanks.
I Review The state of strain at the point has components of e, = 230 (10 6), e, = -240 (10 ), and Yay = 500 (10 6). Part A Use the strain-transformation equations to determine the equivalent in-plane strains on an element oriented at an angle of 30 ° counterclockwise from the original position. (Figure 1) Enter your answers numerically separated by commas. AEo 1 vec E, Ey', Yr'y = Figure étv
Problem 2 refers to the following: a load P is applied to the cantilever beam shown which causes it to bend and deflect elastically: 2. a. b. 6 C. Gage 1 2 3 4 5 6 5 3 4 on bottom Strain (ue) A student group recorded the following strains from the loaded beam but failed to record which gages (1-6) the strain recordings came from (all strains are in microstrain): -154, 318, -23, 555,-323, 81. 2 1 Write the correct strain readings in the table above. Note gages 1, 3, 4, and 5 are longitudinal gages, and gages 2 and 6 are transverse gages. Gage 4 is on the bottom of the beam and is the same distance from the load as gage 3. Calculate an estimate of Poisson's ratio for this material. If the elastic modulus for this material is 10 Mpsi, calculate the uniaxial stress at the location of gages 5 & 6.
I keep geting numbers for the resultant angle that are definately wrong. can you help me figure out how to get the calcualtion right?