QUESTION 3 Consider a system model given by d²x (1) dx (1) d1² dt x (0) = 1 dx (1) dt +4 +5x (t) = f(t) r=0 What is the impulse response function? 'sint = 1. о зе sint+e -21 O 3e 'sint+e' O-4e-2¹ sint - 2e-21 cost -21 cost+2 -21 sint+e -21c sint - 2cost + e-¹ cost + 2 cost

Q: 1- For the system shown in Figure 2 a) Find system response when r(t) = 0 and 2(t) is unit step b)…

A: this question about the moment of inertia of the shaded region about the centroidal x and y axes.…

Q: Consider the closed loop system with response shown in following figure. What is the 10%-90% rise…

A: Rise time in control systems refers to the amount of time it takes for a system's reaction to reach…

Q: Figure 1 shows an electrical system comprising a series RLC circuit and input voltagesource…

A: Step 1: Step 2:

Q: b. Using Simulink, simulate the transfer function airflow response, Q(t) (air entering respiratory…

A: Doing et al. explained that the different ranges of R. Rp.1, and, C parameters are observed for both…

Q: 5. Sketch the following function in frequency domain plot: i. Y(t) = 3 sin (4лt) + 4 cos (4 лt) ii.…

A: Given data i)  Y(t) = 3 sin (4πt) +  4 cos (4πt)ii) Y(t) = 12 sin (10πt) + 5 sin (20πt) +  sin…

Q: 1. Consider the equation of motion of a single degree of freedom with the forcing function as shown…

A: Total response of system at t=1 second is approximately = .004111 phase angle = 0 final answer…

Q: What is the damping ratio of the following system transfer function? G (s) 27 s2 +1.8s+9 0.9 0.3 O…

A: Correct option: 0.3

Q: at DMZ For the following Second-order system and initial conditions, find the transient solution:…

A:

Q: 0 K>-6 Ok>0 OK>-3 s³ +s² (K+6) + s(6K+9)+9K = 0 If characteristic equation is minimum value for k to…

A: The minimum value of k. Given: The characteristic equation is s3+s2K+6+s6K+9+9K=0

Q: 11-30X in its model name.) 1. Consider the steady-state response of a first-order system given by V…

A: Solution: Given Data: Vt=120 sin4t-60   To Find: (a) Determine the amplitude A, angular frequency ω,…

Q: Match the following two frequency response diagrams: 40 iu 0.4 0.2 Response A 0 10 |G(i w)| 5 6…

A: The first curve has a wave form of continuous. This means that there is a damping in the system…

Q: 6. Consider the mechanical system shown in Fig. 8. Let V(t) be the input and the acceleration of the…

A: Below is the clarified and detailed explanation for above tricky question....if you are ok with my…

Q: 3 points the Laplace transform of e-2t cos(3t) + 5e-2t sin(3t)

A:

Q: The system y(t)=x(t)cos[2(pi)t] is O nonlinear time invariant nonlinear time variant O linear time…

A: Given data: yt=xtcos2πt Need to determine the type vibration is.

Q: a) Consider the system shown in Figure Q3a, consisting of a spring connected to the free end of a…

A: Step 1: Step 2: Step 3: Step 4:

Q: ġ(t) ти x(t) k v(t) ➤f(t) Figure 1: A model of piezosensors Figure 2: A load cell to measure force…

A: 1. Notations and Given ValuesLet's define the following notations based on the textual description…

Q: Y(s) U(s) G₁(s) G₂(s) (a) H₁(s) H2(s) Figure Q6 Using Routh test determine if the system shown in…

A: Step 1:

Q: Determine the steady-state (forced) response and the time constant (or dominant tin each of these…

A:

Q: Figure 2). 1.2 1 0.8 Peak value: 1.1878 0.6 Peak time: 2.0723 sec 0.4 splacement of mass

A:

Q: 5. Calculate the response of the system below 27 -3 [ 8 1 ] * 0 + [2] 3³] × 0) = 0 (t) -3 given the…

A: Step 1: Step 2:

Q: Considering the following system s+3 G(s) = s(s+1)(s+5) In the Bode plot, what is the slope of the…

A:

Q: QUESTION 2 Consider a system model given by d²x (1) dt² 2- + 3x (t) = 48 (1) x (0) =1 dx (t) dt =…

A: Given:The system model is given below;