Consider the closed loop system with response shown in following figure. What is the 10%-90% rise time of the response? Give your answer in seconds to the nearest third decimal place. Do not enter the units. Amplitude 1.4 1.2 1 E 0.8 0.6 0.4 0.2 0 0 0.05 THI 0.1 0.15 Time (seconds) 0.2 0.25 0.3 0.35

Q: For the following RRR manipulator and the matrix showing its forward kinematics C123 -8123 0.0 1c1 +…

A: Given Data T30=c123-s1230.0l1c1+l2c12s123c1230.0l1s1+l2s120.00.01.00.00001 Now…

Q: Determine the coefficients (a and b) for the baseflow (Qb) in using the data below. Find values for…

A:

Q: A thermocouple is connected to a data acquisition system which is used to measure temperature of air…

A: Given: The time constant, t = 0.5 s The frequency, w = 2 rad/s The amplitude, To = 10 C

Q: F(kN) = x¹ + 2x orce to displacement at 1 cm by dith

A:

Q: A car with a mass of 83 kg, including driver, travels a rough road with bumps spaced 5.5 m apart. At…

A: The mass of car is The distance between the bumps is .The speed is The mass of passenger is .The…

Q: ) Based on the vibration signal shown in Figure determine the damping ratio, natural frequency and…

A:

Q: A certain system contains three branches in parallel. One branch contains units A and B in series. A…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Match the following two frequency response diagrams: 40 iu 0.4 0.2 Response A 0 10 |G(i w)| 5 6…

A: The first curve has a wave form of continuous. This means that there is a damping in the system…

Q: 3 points the Laplace transform of e-2t cos(3t) + 5e-2t sin(3t)

A:

Q: Solve the following differential equation in Matlab using ode45.m. Use time interval of 0.1 second.…

A: Here, we have a differential equation given as:And, the initial condition is,So, we have to find the…

Q: Show your calculation for the method 2 velocity. Explain how it compared to the reading from your…

A: Write the given data from the table. t1=5 sx1=11 mt2=6 sx2=17 m

Q: Two cryptographers encrypt a secret password consisting only of nonnegative integers less than…

A: The least positive integer a that could be used in their keys is 54.Explanation:Step 1: First find…

Q: Review the Outpatient Clinic Case 410057 in AHIMA VLab, which can be found in Authentic Patient…

A: The first step is to review the diagnosis codes. The primary diagnosis code is C50.312, which refers…

Q: 5.47 For the circuit involving ideal op amps shown in the image below, if R1 = 8 k2, R2 = 27 k2, R3…

A:

Q: QUESTION 1 Solve the following differential equation in Matlab using ode45.m. Use time interval of…

A: To solve the given differential equation in MATLAB using `ode45.m`, we can follow these steps:1.…

Q: Problem 4-1: During a step function calibration, a first-order instrument is exposed to a step…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.