Show your calculation for the method 2 velocity. Explain how it compared to the reading from your velocity vs. time graph. between the these times use the equation: At = 6.0 s – 5.0 s. In the same way, youshould be able to calculate the displacements.Now you will need to calculate the average velocity within the time interval: The equationAx6 тfor average velocity is: ū =. ū =1sIn this example case we have: iAtFind the time that is best associated with the average velocity you calculated in the timeinterval. For example, in the interval between the times, what is the time that the cartmost likely had an instantaneous velocity equal to the average velocity in that interval?It is the time in the middle between the 1st and 2nd time. The time directly in the middlebetween them can be calculated by using the equation for middle or average values:t1 + t2tmiddle25.0 s + 6.0 stmiddle2tmiddle = 5.5 sTherefore, using this method, an instantaneous velocity of v = 6.0“ is best associatedwith the time instant t = 5.5 s. The slope of the tangent line at this time should be thesame value as this calculated velocity.Using the data from your table include the following as part of your analysis:Select two data points from your table. Make them adjacent points.Show your calculation to find the average velocity between these points.Show your calculation to find the mid-time, the time when the car has an instantaneousvelocity the same as the average you calculated.Use your velocity vs time graph and how the value of the velocity at the mid-time fromthe best-fit line.Compare the calcuation with the graph reading at the mid-time. Method 2 using information from the data table: Calculating the average velocity between twovalues of position and time.time (sec)Position (m)Notice that the header isnot complete. Do youknow what is missing?ExampleBe sure to make the5.011.0Calculationheaders in your table6.017.0complete.Here is an example using two position/time data points to calculate the velocity at themid-time. Calculate the time interval. For example, to calculate the time interval

Write the given data from the table. t1=5 sx1=11 mt2=6 sx2=17 m

Answered: Show your calculation for the method 2…

Show your calculation for the method 2 velocity. Explain how it compared to the reading from your velocity vs. time graph.

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

Similar questions

1. The graph in Fig. A shows the velocity of an ambulance vehicle driver plotted as a function of time. How far does the officer go in the first 3 seconds? The first 7 seconds? The first 11 seconds? Vx (m/s) 50 45 40 35 30 25 Fig. A 20 15 10 5 t (s) 2 4 6 !8 10 12 14 7 11 3.
can I get simplest way to get that answer ....
Q1/ The figure below shows such an LSPB trajectory, where the maximum velocity V 60 deg/sec. In this case, the times are given as t.= 5 sec and t 30 sec. In addition, the joint angles in beginning and the ending q=20 deg and qf = 70 deg , respectively. For these required data , determine the following : 1- The position function and its profile. 2- The velocity function and its profile. 3- The acceleration function and its profile. 4- The function of jerk variable and what is the nature of jerk? 5- The position, velocity, and acceleration at tm-13 sec. te tm ty te ty t
(1-C.s) m/s² where Cis a constant and sis Q13. The acceleration of a particle traveling along a straight line is a the position in m. If the constant Cis 0.1, the initial velocity vo is 0, and the initial position so = 1.7 m at time t = 0, determine the particle's velocity v when its position s = 4.8 m. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point, and proper Sl unit. Answer: =
Use t'=20.4 instead of 8.4 and use the formulas attached