Question-3:(a) In a consolidated drained triaxial test, a specimen of saturated sand failed under andeviator stress of 250 kN/m², when the cell pressure was 100 kN/m².i.Illustrate by drawing the Mohr circle for the failure stress condition.Solve for ø' and the theoretical inclination of the failure plane to theii.horizontal.iii.failure.iv.Solve for the shear stress on the failure plane and maximum shear stress atSolve for factor of safety with respect to shear strength on the plane ofmaximum shear stress?

Answered: Image /qna-images/answer/f6b00b27-93bf-4604-8d26-bdb3e9166dcb.jpg

Question-3: (a) In a consolidated drained triaxial test, a specimen of saturated sand failed under an deviator stress of 250 kN/m², when the cell pressure was 100 kN/m². i. ji. Illustrate by drawing the Mohr circle for the failure stress condition. Solve for ' and the theoretical inclination of the failure plane to the horizontal. ii. Solve for the shear stress on the failure plane and maximum shear stress at failure. iv. Solve for factor of safety with respect to shear strength on the plane of

Question-3: (a) In a consolidated drained triaxial test, a specimen of saturated sand failed under an deviator stress of 250 kN/m², when the cell pressure was 100 kN/m². i. ji. Illustrate by drawing the Mohr circle for the failure stress condition. Solve for ' and the theoretical inclination of the failure plane to the horizontal. ii. Solve for the shear stress on the failure plane and maximum shear stress at failure. iv. Solve for factor of safety with respect to shear strength on the plane of

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3 A sample of soil was subjected to a series of triaxial tests. The results were as shown in the table. If a third test is made with a cell pressure of 250 kPa. Determine the value of the maximum principal stress (in kPa) for the third test. 03 (kPa) 60 130 0₁ (kPa) 165 280 The value must be a number
9. A consolidated drained test was carried out on a sandy clay under a cell pressure of 250 kPa. A constant back pressure of 120 kPa applied throughout the test. The dimensions of the sample were 76 mm x 38 mm. Addional test data recorded at failure were: Load transducer force = 368 N 3 Measured change in volume = 2.42 x 10 m³ Axial deformation = 2.05 mm Determine the major principal stress, o, at failure. (455 kPa)
A specimen of saturated sand was subjected to a tri-axial test under a confining pressure of 450 kPa. If the drained friction angle is 34°, determine: The normal stress at failure (in KPa).
CU tests were carried out on identical clay samples. Each the sample has a diameter of 63.4 mm and a height of 152.4 mm. Defeat The conditions in the event are presented below: The total and effective stress on failure includes Mohr circles and Draw the effective and total stress M-C failure envelopes. Total and determine the effective strength parameters.
A sample of dry sand is tested in direct shear. The shear box holding the sample has a circular cross section with a diameter of 50 mm. The normal (compressive) load imposed is 200 N. The sample shears when the shear force is 130 N. (a) Determine the test normal stress and shear stress at failure.
A dilatometer test (DMT) was conducted in a clay deposit. The water table was located at a depth of 3 mbelow theground surface. At 8 m depth the contact pressure (p1) was 280 kPa and the expansion stress (p2) was 350 kPa.Assume σo = 95 kPa at the 8 m depth and μ = 0.35. Determine (a) Coefficient of at-rest earth pressure Ko,(b) Overconsolidation ratio OCR and (c) Modulus of elasticity Es.
A consolidated drained tri-axial test was conducted on a normally consolidated clay. The results were as follows: 03 = 300 kPa (confining pressure) Deviators stress = 300 kPa 0 Compute the angle of shearing resistance. Compute the angle that the failure plane makes with the major principal. stress. Compute the shear stress on the failure plane.
Following data are given for a direct shear test conducted on dry sand: Cylindrical specimen dimensions: diameter = 50 mm and height = 25 mm Normal stress: 0.15 N/mm2 Shear force at failure: 276 N Determine the angle of friction of this soil. Normal Stress = 0.15 N/mm2 Shear Force = 276 N Shear Force = 276 N
A drained triaxial test on the normally consolidated clay showed that the failure plane makes an angle of 58 with the horizontal. If the sample was tested with a chamber confining pressure of 103.5kPA, what was the major principal stress at failure? (Unit in kPa) (Answer only number(whole number without unit)
A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shearing stress on the failure plane were determined to be 75kPa and 42kPa, respectively. Determine the angle of internal friction of the sand, in degrees.Determine the axial stress applied to the specimen, in kPa.
A sample of ocean sand was retrieved from 7 m below the surface. The sample had been under a vertical stress Ov of 150 kN/m³, a horizontal stress Oh of 250 kN/m³, a shear stress of 86.6 kN/m. If the angle theta between the vertical stress and the principal stress is 60°, calculate the angle of internal friction of the soil. [Hint: you must sketch the Mohr circle of stresses] Please explain clearly and step by step
Calculate and then plot the change in total stress, effective stress and pore water pressure with the plate for the soil layers shown in the figure below and according to the conditions: • There is no effect of capillary action • There is an effect of capillary action at a distance of 2m above the water level in the sandy layer