Question 2 Steam at 320ºC flows in a stainless steel pipe, whose inner and outer diameters are D₁ = 5 cm and Do 5.5 cm. The pipe is insulated with insulating material - glass fiber (organic bonded) at a thickness of 3 cm. Heat is lost to surroundings at 5°C via convection and radiation with a combined heat transfer coefficient of h₂ = 18 W/m²K. If the heat transfer coefficient inside the pipe is h₁ = 60 W/m²K, determine: a) the heat loss from the steam per unit length of pipe b) temperature drop across the pipe thickness

Question 2 Steam at 320ºC flows in a stainless steel pipe, whose inner and outer diameters are D₁ = 5 cm and Do 5.5 cm. The pipe is insulated with insulating material - glass fiber (organic bonded) at a thickness of 3 cm. Heat is lost to surroundings at 5°C via convection and radiation with a combined heat transfer coefficient of h₂ = 18 W/m²K. If the heat transfer coefficient inside the pipe is h₁ = 60 W/m²K, determine: a) the heat loss from the steam per unit length of pipe b) temperature drop across the pipe thickness

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: It is required to perform a heat treatment for gas turbine applications, for them it is required to…

A: From the given data: The fourier number will be: →Fo=kρCP×tLC2Where LC=characteristic length=D=3.5…

Q: A long, thin copper rod 5 mm in diameter is exposed to an environment at 20°C. The base temperature…

Q: Heat is generated in a 2.0-cm-square copper rod at the rate of 30 MW/m³. The rod is exposed to a…

A: Given data: a=2.0 cmQ˙=30 MW/m3T∞=25°Ch=5 kW/m2 Need to determine the surface temperature of the…

Q: A metal cube of 0.1 m sides is being cooled down uniformly from 300°C to 30°C by placing it in cold…

Q: Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate…

Q: Q2 : A hot surface at 100°C is to be cooled by attaching 0.25 3 cm long, 0.25 cm diameter aluminum…

Q: An aluminum pan with a thermal conductivity of = 237 /m.K is used to heat water as shown in the…

A: As per given D=15cm K=237 w/m°c Q=1400w T=105°c We have to determine temperature of outer surface

Q: a) On a unit surface area basis, determine the rate of heat transfer into and out of the wall and…

A: From Fourier's Law q =-kdTdxx=0=-1d200-200x+30x2dxx=0=200-60*0= 200 W/m2

Q: Q1) The wall of a drying oven is constructed by sandwiching an insulation material of thermal…

Q: We are testing a thin, transparent film heater that is bonded to the inside of an automobile window…

A: Thickness of atuomobile window, t=3 mmSurface area of window, A=0.6 m2Air temperature inside the…

Q: Heat is generated in a sphere of radius 1 m at a rate of 1000 W/m3. The sphere is surrounded by air…

A: The radius of sphere is The heat generation rate is The temperature of air is The thermal…

Q: An experiment was conducted to determine surface convective heat transfer coefficient for peas being…

A: To find:Determine the surface heat transfer coefficient.

Q: A hot gas at 300°C with convective heat transfer coefficient of 100 W/m²-K is flowing through an…

A: Given:Hot gas temperature, Tg=300oCConvective heat transfer coefficient of hot gas, hg=100…

Q: You are cooking asparagus for dinner. The asparagus is fried in oil at a temperature of 230 C. You…

A: First of all we need to assign an inner diameter to the asparagus because there are not much…

Q: You are pouring a concrete pad 0.1 m thick. The curing of concrete is an exothermic chemical…

Q: = 16 W/m.K. The inner diameter and thickness of the pipe are 26 cm and 1 cn espectively. The…

A: Boundary Conditions T( r1 ) = T1 =350oC T( r2 ) = T2 = 28oC dTdr=C1r T(r) = C1 lnr + C2 T( r1 ) =…

Q: Steel is sequentially heated and cooled to relieve stresses and to make it less brittle. Consider a…

A: SteelExplanation:Step 1:Step 2:Step 3: Step 4:

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An insulated pipe has an inner diameter of 0.05 m and an outer diameter of 0.06 m. If the insulation is 40 mm thick, calculate the heat transfer rate per metre length. You can assume K pipe 220 W/m.K, K insulation 2.2 W/m.K, inner pipe wall temperature is constant at 120 oC and the outer insulation surface is at 20oC.
A concrete slab of a basement is 11m long, 8m wide and 0.20m thick. During the winter, temperatures are nominally 17C and 10C at the top and bottom surfaces. The concrete has a thermal conductivity of 1.4W/m-K, The basement is heated by a gas furnace operating at an efficiency of 0.90 and natural gas is priced at $0.001/MJ. What is the daily cost of heat loss in dollars?
Heat transfer
Shown below is an insulated copper block that receives energy at a rate of 100 W from anembedded resistor. If the block has a volume of 10-3 m3and an initial temperature of 20oC, howlong would it take, in minutes, for the temperature to reach 60oC? Copper has a specific heatcapacity ccu = 0:385 kJ/ kg.K and a density of cu = 8930 kg/m3.
Q2: A 2.5 -mm-diameter electrical wire is insulated by a 2-mm-thick rubberized sheath (* = 0.11 W/m K), and the wire/sheath interface. The convection heat transfer coefficient of the outer surface of the sheath is 10 W/m² K, and the temperature of the ambient air is 20 C. If the temperature of the insulation may not exceed 50 C, what is the maximum allowable electrical power that may be dissipated per unit length of the conductor? What is the critical radius of the insulation?
A room is well insulated apart from a single-glazed window measuring 1 m2 and 4 mm thick. The internal air temperature is 22oC and outside it is -12oC. If the external convective heat transfer coefficient, hout, is double that of the inside coefficient, and the conductivity in the glass is negligible. Determine hout if Q = 100 W.
Suppose that the 10 cm thick concrete wall of a commercial building measures 30 mby 4 m. The energy impinging on the surface is 700 Wm-2. Under these conditionsthe external air temperature is 25ºC, and the internal and external surfacetemperatures of the concrete wall are 17ºC and 40ºC, respectively.(a) State and briefly describe the three heat transfer mechanisms.[30%](b) Calculate the net amount of thermal energy radiated by the wall.[40%](c) State your assumptions and briefly discuss their effect on the relativesizes of the heat transfer mechanisms.[30%]Data for Question A3.Heat transfer coefficient of air at 25ºC = 5 Wm-2K-1Thermal conductivity of concrete = 1.2 Wm-1K-1Emissivity of concrete = 0.85Stefan’s constant = 5.7 x 10-8 Wm-2K-4
Question #7 Steam at 320°C flows in a stainless steel pipe (k-15W/m K) whose inner and outer diameter are 5cm and 5.5cm respectively. The pipe is covered with 3cm thick glass wool insulation (-0.038W/mK). Heat is lost to the surroundings at 5°C by natural convection and radiation, with a combined natural convection and radiation heat transfer coefficient of h 15W/m² K. Taking the heat transfer coefficient inside the pipe to be happe = outside pipe = 80 W/m²K. (A) Draw the schematic diagram of this problem and label all quantities. (B) Draw the thermal network diagram of this problem and label all thermal resistors and the direction of heat flow. (C) Determine the (i) inner surface area (ii) outer surface area (iii) inner thermal resis- tance (iv) outer thermal resistance (v) thermal resistance across pipe and (vi) thermal resistance across insulation. (D) Determine the total thermal resistance for the unit length of pipe. (E) Determine the rate of heat loss from the steam per unit…
2-9 A steel tube having k = 46 W/m- °C has an inside diameter of 3.0 cm and a tube wall thickness of 2 mm. A fluid flows on the inside of the tube producing a convection coefficient of 1500 W/m² . °C on the inside surface, while a second fluid flows across the outside of the tube producing a convection coefficient of 197 W/m2.°C on the outside tube surface. The inside fluid temperature is 223°C while the outside fluid temperature is 57°C. Calculate the heat lost by the tube per meter of length.
4. Two aluminum blocks with different dimensions, but the same mass are shown in the figure. The dimensions of block 1 are 0.25 cm in thickness, 3 cm in width, and 36 cm in length. The dimensions of block 2 are 3 cm for each side of the cube. Aluminum has a density of 2700 kg/m³ and a specific heat capacity of 900 J/kg-°C. The value of the heat transfer coefficient to the surrounding air is 10 W/m²-°C. 0.25 cm 36 cm 3 cm 3 cm Block 1 3 cm Block 2 3 cm Complete the following. (a) Calculate thermal time constant (in min) for both blocks. (b) Each block is heated to an initial temperature 120 °C and then allowed to cool in the surrounding air which is at 20 °C. Write a script file in MATLAB® that plots the temperature as a function of time, T(t), for both blocks on the same graph. Plot the temperature of block 1 using a solid black line and the temperature of block 2 using a dotted black line. Plot for a duration equal to four of the longer time constant between blocks 1 and 2. The time…
1- A solid infinitely long cylinder, radius 2 cm, has uniform internal heat generation. The temperature distribution in the cylinder is T(r) = = 256 – 8.6 x 104 r² where r is in meters, T in °C and the thermal conductivity of the cylinder material is 16 W/ m °C. Determine: (a) The temperature at the centerline. (b) The surface temperature. (c) The heat flux at the surface. (d) The rate of heat transfer to the surrounding per unit meter of cylinder length.
plz answer this ASAP,thx One surface of a copper plate that is 3 cm thick has a constant temperature of 400 ° C while the temperature of the other surface is kept constant at 100 ° C. Describe the temperature profile and how much heat is transferred across the plate ?, k copper = 380 watts/m.k with a cross -sectional area of 4 cm².