Question 2:A. Choose one of the given four words or numbers to match the blanks in the followingsentences:1.Size of the Interrupt Vector Table (IVT) for the 8086 Microprocessor is ---- Kbytes.(1) 1(II) 2(III) 3(IV) 42.CALL FAR isbytes instruction.(1) 5(11) 4(III) 3(IV) 23.One Bus Cycle in the 8086 Microprocessor consists of ---- clocks.(1) 2(II) 4(III) 6(IV) 84.pin is used to insert wait state into the 8086 Microprocessor.(II) HOLDA(III) WAIT(IV) READY5.(1) HOLDRESET when applied forces the 8086 to execute instruction at logical address ------(1) OFFFFH(II) OOFFOH(III) OFFFOH(IV) FFFFOH6.Clock input for the 8086 Microprocessor should have duty cycle.(1) 22(11) 33(111) 44(IV) 557.In Static RAM each bit is stored in a(1) transistor(II) diode(III) flip-flop(IV) LED8.Mantissa for the single precision real number representation using IEEE-754 consists of ----- bits.(1) 20(11) 21(III) 22(IV) 239. Instruction Queue for the Intel 8086 Microprocessor contains ---- bytes.(1) 6(II) 8(III) 10(IV) 1210. The 8288 Bus Controller is interfaced to the 8086 Microprocessor when it works in(II) Maximummode..(1) Minimum(III) Medium(IV) Smallteti

We are authorized to answer only 1 question at a time since you have not mentioned which question…

Question 2: A. Choose one of the given four words or numbers to match the blanks in the sentences: 1. Size of the Interrupt Vector Table (IVT) for the 8086 Microprocessor is ---- (1) 1 -Kbytes. (11) 2 (III) 3 (IV) 4 2. CALL FAR is bytes instruction. (II) 4 (1) 5 (HI) 3 (IV) 2 3. One Bus Cycle in the 8086 Microprocessor consists of clocks.. (11) 4 (2 (II) 6 (IV) 8 0086 Microprocessor.

Question 2: A. Choose one of the given four words or numbers to match the blanks in the sentences: 1. Size of the Interrupt Vector Table (IVT) for the 8086 Microprocessor is ---- (1) 1 -Kbytes. (11) 2 (III) 3 (IV) 4 2. CALL FAR is bytes instruction. (II) 4 (1) 5 (HI) 3 (IV) 2 3. One Bus Cycle in the 8086 Microprocessor consists of clocks.. (11) 4 (2 (II) 6 (IV) 8 0086 Microprocessor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sometimes "bubbles" are used to indicate inverters on the input lines to a gate. What are the equivalent gates for those shown in the figure below? Hint - use DeMorgan's Law. A B C=A+B (a) D F=DE E (b)
Design 2-bit synchronous counter that counts 0, 1, 2, 3 in succession. Thank you.
The only technique to clear all the flip flops in a serial-in serial-out, shift-register is to clock-in as many Os as flip flops are in the register. O True O False
Q3) a- Draw the logic diagram for a circuit that will divide the (fCLK) by 16. Use (-ve) edge triggered (J-KFF). b- Calculate the (fcLk) if the fout =(÷) MHz ----
Q1: B- Fill out the following blanks: .3-The first 1- Bus-snooping is used for.......2- Two examples of status-flag registers.... computer that used 32-bit microprocessor was......... 4- The inter-processor communication via .5- If a system uses 16-bit address bus, it can reach memory locations up to.......6- Cache memory uses two algorithms for writing... 7- SRAM is better than DRAM due to.......
q3mp plz provide answer for this question
1. Design a 10-state Johnson counter using minimal number of 74HC194 ICs and external gates. Assume that 74HC194 is cleared to zero initially and the register contents are to be shifted right at each clock pulse. D. D D: D, (3) (4) (5) (6) (1) CLR 74HC194 (9) Bidirectional (10) Shift Register (2) SR SER (7) SL SER CLR S1 so Function (11) CLK Reset (Async.) Hold (Do nothing) Shift right Shift left (15) (14) (13) (12) L L SR SER: Shift-right serial input SL SER: Shift-left serial input H L H Parallel load Figure 1. Block diagram of 74x194 IC.
State the difference between type BIT and type STD_LOGIC. Why does STD_LOGIC have so many values?