Question 2: A residential building construction development is using columns that are 4.2m in hieght. The columns are made from seasoned Western Hemlock of Grade F14, with nominal dimensions of 190x45. Intermediate restraints are provided at 1.05m centres to minimize buckling about the minor axis. For the columns under consideration, intermediate restraints for minimizing buckling about the major axis are located at 2.1m centres. The columns can be considered as secondary members as they are closely spaced enabling load sharing. The columns carry unfactored compressive loads as follows: a permanent (dead) load of 50KN, an imposed (live) roof load of 30kN and wind load of 10kN. Assume that the imposed roof load is infrequent in nature (construction related) and that both the long-term imposed (live) load factor (y) and combination factor for imposed action (y) are equal to zero. Location: Rockingham, Western Australia. Check the ability of the column to support the applied loads if the column is restrained at both ends in position and direction.

Question 2: A residential building construction development is using columns that are 4.2m in hieght. The columns are made from seasoned Western Hemlock of Grade F14, with nominal dimensions of 190x45. Intermediate restraints are provided at 1.05m centres to minimize buckling about the minor axis. For the columns under consideration, intermediate restraints for minimizing buckling about the major axis are located at 2.1m centres. The columns can be considered as secondary members as they are closely spaced enabling load sharing. The columns carry unfactored compressive loads as follows: a permanent (dead) load of 50KN, an imposed (live) roof load of 30kN and wind load of 10kN. Assume that the imposed roof load is infrequent in nature (construction related) and that both the long-term imposed (live) load factor (y) and combination factor for imposed action (y) are equal to zero. Location: Rockingham, Western Australia. Check the ability of the column to support the applied loads if the column is restrained at both ends in position and direction.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assessment Task 3 The main roof truss of a resort is to be built using MGP12 grade seasoned radiata pine. The roof truss is shown in Figure 1. The centre section of the bottom chord is subjected to a strength limit state tensile force of 10.2 kN due to permanent loads. The self-weight of the truss in addition to other roof furniture contributes to a strength limit state bending moment in the member of 0.32kNm. The nominal thickness of available timber for bottom chord is 35 mm. Commercially available depths are given in Table 1. Connections at the ends can be assumed to be through 2-M16 bolts, in 18 mm diameter holes for each bolt. Based on strength limit state, design the most economical depth for highlighted member to meet the design loads. Axial tension: factored permanent load =10.2kN Flexural: Factored permanent load = 0.32kNm Location: Melbourne, Victoria. Note that the lateral restraints are at the nodes only and due to diagonals and bracing between trusses. TABLE 1- Available…
A tied column of dimensions 300x450mm is reinforced with 6 bars of 28mm diameter. Also, ties of 10mm diameter are used at a spacing of 300mm. The compressive strength of concrete is given as 28MPa and the yield strength of steel is given as 420MPa. Determine the maximum ultimate load on the column.
6.
(1) The out-plane stability formula of beam-columns recommended in the design code is as following:< N BMx -17 sf = Q, A PbWLx Please describe the definitions of , and b, how are they determined? E please asap this is complete question,
Design a simple span one-way slab to carry a uniformly distributed live load of 18 kPa The span is 34 meters (center to center of supports). Use fc 20.7 MPa and fy276 MPa. -Use NSCP 2015, conform to minimum thickness requirements. Complete solution ty..
Principles of Steel design 1 Why SMF in NSCP 2015? Whats the significance? 2 Why do we study LB and LTB in steel beams? 3 What is effect of KL/r and 2nd order moments in columns?
PLEASE HELP
Try
Correct solution please
H.W.5: For the simply supported beam shown below reinforced by 4025 bars (fy= 420 MPa), the concrete strength (f= 21 MPa) evaluate the following: 1- Check the actual flexural stresses in concrete and steel if the span length equal to (4 m), dead load 8 kN/m including self-weight of the beam, live load equal to 10 kN/m. 2- The length of beam span that makes the concrete in tension face starts to crack. 3- The actual stress in concrete and steel if the span length of the beam is equal to 7 m. WI= 10 kN/m Wd=8 kN/m 420 mm 500 mm 마 350 mm
Please answer ASAP using nscp 2015
Size an A992 W shape given the following information; -Beam span is 20 ft and simply supported -Floor beams are 6 ft on center -Cb=1.0 (don't forget self-weight) -The beam will support a plywood deck (3 PSF) oriented perpendicular to the beam -The average concrete (normal weight) thickness is 4.5 in Assumption - 50% ponding factor during the concrete placement and treat the concrete as a live load - 10 Psf for the concrete workers live load - Plywood framework is used instead of steel decking - the beam has no support of the compression flange over its length