A steel composite beam section is shown in Fig. 2. The beam is simply supported with a span of 6.5 meter. It is required to: (1) Determine the flexural strength of the composite beam with the full composite action; (2) Calculate the spacing (s) of the shear stud to ensure the full composite action if the strength of one shear stud is 45 kN. Beff 200 .. 55 C30 Concrete S Shear Stud 30 - - 15 400 S235 steel 30 250 6500 Fig.2. Steel composite beam (mm).

A steel composite beam section is shown in Fig. 2. The beam is simply supported with a span of 6.5 meter. It is required to: (1) Determine the flexural strength of the composite beam with the full composite action; (2) Calculate the spacing (s) of the shear stud to ensure the full composite action if the strength of one shear stud is 45 kN. Beff 200 .. 55 C30 Concrete S Shear Stud 30 - - 15 400 S235 steel 30 250 6500 Fig.2. Steel composite beam (mm).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Of a reinforced concrete column under pure axial load given its cross-section dimensions, a) Determine the total longitudinal reinforcement area of the section you are reinforced according to the ratio of Ø18 reinforcements and the minimum reinforcement. b) Calculate the amount of axial load that the section can bear. m=1,n=4 Cover value will be taken as 35 mm. For the material, it will use C25/30 – S420
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
Final answer must be 2 decimal places, dont round off initial values ty
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
42 Mm 28 Mm A B 36 Mm Determine The Moment Of Inertia And The Radius Of Gyration Of The Composite Section With Respect To An Axis Which Is Parallel To The Plate And Passes Through The Centroid C Of The Section.
1 Situation 19. A composite beam shown is subjected to a bending moment of 500 kN-m. Determine the maximum flexural stress; 300 VIEW INNOVATIONS 200 200 100 55. Experienced by the steel 56. Experienced by the aluminum A. 0.03 B. 25.24 57. Experienced by the brass A. 25.24 B. 37.86 REVIEW I EW INNOVATIONS Steel, E=200 GPa Aluminum, E=70 GPa Brass, E-105 GPa wwwww C. 48.2 D. 72.11 C. 16.8 C. 16.8 D. 11.21 VIEW INNOVATIONS REVIEW INNOVATIONS REVIEW IS
Required information A composite beam is made by attaching the timber and steel portions shown with bolts of 12-mm diameter spaced longitudinally every 200 mm. The modulus of elasticity is 10 GPa for the wood and 200 GPa for the steel. The vertical shear is 4.4 kN. 12 mm 250 mm 12 mm 150 mm- Determine the average shearing stress in the bolts. (Round the final answers to two decimal places.) The average shearing stress in the bolts is MPa.
Asiacell lln. H.W. No.1 For the simply supported solid one way reinforced concrete slab shown in the figure below having a span of (L= 4m), check the following requirements using strength method: a- Slab thickness b- The spacing between reinforcement for main and shrinkage reinforcement c- The actual reinforcement with minimum reinforcement d- Calculate ultimate resisted moment that can be withstand by the slab e- Determine the ultimate uniformly distributed load carried by slab. f = 25 N/mm2 fy=420 N/mm² + 10mm@s00mm shrinkage h=200mm -L=4m- $12mm@200mm main
The two pieces of wood, 2 in. by 4 in., are glued together along the 40o joint. Determine the maximum safe axial load P that can be applied if the shear stress in the glue is limited to 250 psi
Size an A992 W shape given the following information; -Beam span is 20 ft and simply supported -Floor beams are 6 ft on center -Cb=1.0 (don't forget self-weight) -The beam will support a plywood deck (3 PSF) oriented perpendicular to the beam -The average concrete (normal weight) thickness is 4.5 in Assumption - 50% ponding factor during the concrete placement and treat the concrete as a live load - 10 Psf for the concrete workers live load - Plywood framework is used instead of steel decking - the beam has no support of the compression flange over its length