For the simply supported solid one way reinforced concrete slab shown in the figure below having a span of (L- 4m), check the following requirements using strength method: a- Slab thickness b- The spacing between reinforcement for main and shrinkage reinforcement c- The actual reinforcement with minimum reinforcement d- Calculate ultimate resisted moment that can be withstand by the slab e- Determine the ultimate uniformly distributed load carried by slab. S = 25 N/mm? fy=420 N/mm? + 10mm@s00mm shrinkage h-200mm L=4m- $12mm@200mm main

For the simply supported solid one way reinforced concrete slab shown in the figure below having a span of (L- 4m), check the following requirements using strength method: a- Slab thickness b- The spacing between reinforcement for main and shrinkage reinforcement c- The actual reinforcement with minimum reinforcement d- Calculate ultimate resisted moment that can be withstand by the slab e- Determine the ultimate uniformly distributed load carried by slab. S = 25 N/mm? fy=420 N/mm? + 10mm@s00mm shrinkage h-200mm L=4m- $12mm@200mm main

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.8.8P

See similar textbooks

Similar questions

O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'
I need the answer as soon as possible
Please give explanations and formulas
What is the characteristic strength of a mild steel reinforcement bar? Select one: O a. 415 N 415 N/mm O C. 250 N d. 250 N/mm
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
Civil Engineering The section of a beam near a column is given below. Area of the top reinforcement is 800 mm2 and bottom reinforcement is 300 mm2. Is the section under or over-reinforced if the balanced reinforcement ratio is po =0,0209? bw = 200mmd= 300mm bw a) O Under-reinforced since 800 mm2 Asb e) Over-reinforced since 300 mm2 > Asb What is the distance of the neutral axis c from the top of the beam, if the top portion of the beam is in compression. Concrete is C30, longitudinal steel bars are o16 and made of B420C steel. Use design strengths in computation. b = 800 mm, d = 500mm, h For C30 concrete k = 0.82. your = 100 mm, b, = 300 mm. Hint: a) 53 mm b) O 46 mm c) O 20 mm 32 mm 26 mm
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPaa) depth of the compression blockb) strain in the tension reinforcementc) moment reduction factor
concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @ face supports Top bars 2-20mm 5-20mm Bottom bars 3-20mm 2-20mm Given Stirrup diameter: 10 mm concrete fc = 21 mpa steel rebar fy = 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in single layer calculate the following: a) tensile steel ratio in positive bending moment at midspan (round off to 5 decimals) b) design moment strength of section at midspan for positive bending ( in kN•m , nearest whole number) c) nominal design strength of section at face of support for negative bending ( in kN•m , nearest whole number)
Fotoğraflar - Ekran Görüntüsü (10)_LI.jpg Tüm fotoğrafları görüntüle + Şuraya ekle: Z Düzenle ve Oluştur v E Paylaş The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm diameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stress- strain diagram determine the followings properties of the material (Poisson's ratio of the material is 0.32) : 600 a) Modulus of elasticity 550 500 b) Yield strength 450 c) Toughness 400 350 d) Resilience 300 e) Shear modulus 250 200 f) Bulk modulus 150 g) Ductility as described by 100 percent change in length 50 0.01 0.02 O.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.11 0.12 0.13 0.14 0.15 0.16 0.17 0.18 Strain 18:12 18.01.2021 10 Stress, MPa