Example: Determine the following for the given beam section: fc' = 21 Mpa, fy = 420 MPa 1. Depth of stress block, a, at ultimate stage 2. Tensile steel strain, &t, when concrete &c = 0.003 d=400 mm BOTS SAND 3. Type of Failure 4. Reduction Factor 5. Nominal Strength 6. Design Strength OLO b=250 mm 5- Ø25mm

Example: Determine the following for the given beam section: fc' = 21 Mpa, fy = 420 MPa 1. Depth of stress block, a, at ultimate stage 2. Tensile steel strain, &t, when concrete &c = 0.003 d=400 mm BOTS SAND 3. Type of Failure 4. Reduction Factor 5. Nominal Strength 6. Design Strength OLO b=250 mm 5- Ø25mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a-Design the concrete column to carry the applied load Concrete allowable strength: 35 MPa P= 900 kN Column dimension needs to be 300 mm X B Material reduction factor 0.75 - Load factor 1.5 B mm 300
For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi. For the midspan section shown, check if steel yields and compute ØM, and compare it with M. WD = 1.2 kips/ft plus weight of beam WL = 1.5 kips/ft %3D 20.5 in 23 in 3 no. 9 bars 18 ft 11 in.
For the below given beam: a) Determine the cracking distributed load. b) Determine the stress in concrete and steel under service load if WDL = 15 kN/m; WLL = 10 kN/m Materials: C25; S420 40 mm 1.8 m 560 mm 300 mm
A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 300 mm Over-all depth, h = 425 mm Tension reinforcements = 5 pcs 28 mm dia Comp reinforcements = 4 pcs 20 mm dia Specified strength of concrete, f'c = 28 Мра Steel yield strength, fy = 345 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.
Design a one way slab (as shown in fig) for inside of a building. Normal weight aggregate concrete will be used with a density of 145pcf. Compressive strength of concrete = 4000psi Yield strength of steel = 60000psi LL = 250psf
A concrete specimen with b = d is supported at both ends 600mm apart. It is tested for flexure strength with load at midspan of 100kN and failed with a flexural stress of 52.083 MPa. What is the dimension b and d of the specimen in mm?
calculate the corresponding depth uniform stress block in a reinforce concrete beam 42*10 deep reinforce with bars 20-mm in a diameter enclosed with 10-mm dia stirrups when the tensile steel strain is 0.008 and concrete compression strain 0.003. f'c = 22 Mpa. Express your anser in 2 decimal places only in mm.
Determine the cracking moment (KN/M) and compressive stress felt by concrete (MPa). Show your solutions
A rectangular fixed supported beam has the following properties. Compression steel if required shall have its centroid "d " mm from the extreme fiber. Calculate the required steel area (mm) at the midspan and end supports of the beam. Sketch the location of the reinforcements. Use 23.6 kN/m for the unit weight of the concrete. Round off your final answer in 3 decimal places. Given: width of beam, b = 450 mm depth of beam, h = 650 mm clear cover up to center of tension 60 mm bars= d'= 65 mm f'c = 35 MPa fy = 415 MPa wDL = 72 kN/m wLL = 63 kN/m Length of beam = 12 MIDSPAN: Required Tension Steel Area = mm? Required Compression Steel Area (if needed) - mm2 END SUPPORTS: Required Tension Steel Area = mm? Required Compression Steel Area (if needed) - mm?
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
Determine the cracking moment (KN/M) and the compressive stress felt by concrete (MPa). Show your step by step answer with solution
PROBLEM TO SOLVE: 600 mm 400 mm 6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa) d. Moment of Inertia under critical condition e. Demand Capacity Ratio of Concrete under Compression Stress f. Compression force on concrete (kN) g. Distance of the compression concrete force from the neutral axis (mm)