Question 1: The rectangular rigid-bar-assemblage shown in the figure below consists of three rigid bars interconnected by frictionless hinges. The horizontal displacement at joint 3 is resisted by a translational spring of stiffness ki and the rotation at joint 4 is resisted by a rotational spring of stiffness kr. Determine the buckling load Per and the nature of the equilibrium state (i.e., the load range at which the equilibrium state is stable and unstable, respectively). Dimensions are shown in the figure (width: a; height: h). ww

Question 1: The rectangular rigid-bar-assemblage shown in the figure below consists of three rigid bars interconnected by frictionless hinges. The horizontal displacement at joint 3 is resisted by a translational spring of stiffness ki and the rotation at joint 4 is resisted by a rotational spring of stiffness kr. Determine the buckling load Per and the nature of the equilibrium state (i.e., the load range at which the equilibrium state is stable and unstable, respectively). Dimensions are shown in the figure (width: a; height: h). ww

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stresses acting on element B (see figure part a) on the web of a wide-flange beam are found to be o = 11,000 psi in compression in the horizontal direction and oy = 2,600 psi in compression in the vertical direction (see figure part b). Also, shear stresses of magnitude Tzy = 3,200 psi, act in the directions shown. B Side Cross View Section (b) (а) Determine the stresses acting on an element oriented at a counterclockwise angle of 45" from the horizontal. Round your answers to one decimal place. psi psi psi
The state of stress at a point is the result of two loadings as shown in figure. When acting alone, the first loading produces the 3 MPa pure shear with respect of xy-axis. The second loading alone results in the 4 MPa pure shear with respect to the x'y-axis. The angle between the two sets of axis is 30° as shown. If the two loadings act simultaneously then resultant (absolute) shear stress at that point with respect to x-y axis is MPa (in integer). 3 MPa st 1 loading 2 loading 4 MPa α = 30° x'
The uniform forces U and P are applied to a plate with dimensions of 500mm x 400mm and a thickness of 10 mm as illustrated. Consider the linear elastic behavior, 200GPa Young's modulus, and 78GPa shear modulus. The plate is subjected to a uniform force U with an undetermined magnitude and direction and a uniform tensile force P=50KN. X 500 mm 400 mm A. What is force U, in kN, if deformation along y is zero? Is it a compressive or tensile force? B. What is the x-axis deformation, in mm? Is the dimension growing or shrinking?
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
The figure shows a beam made from a material having an allowable tensile stress of 135 MPa and a compressive stress of 165 MPa. The couple M is applied to the beam in a plane forming an angle of 45° as shown in the figure. a) Determine the location of the centroid of the cross section b) Calculate the moments of inertia about the principal axes, I, and ly c) Determine the maximum allowable internal moment M that can be applied to the beam N M Y 140 mm 140 mm 45⁰ 140 mm 280 mm 140 mm 140 mm
An element is subjected to plane stresses as shown in Figure Q1. (i) Determine the normal stress and shear stress acting on the plane that is inclined at 20° as shown in the figure. (ii) Determine the principle major and minor stress and the orientation of the plane where the stresses acting. (iii)Determine the maximum shear stress and the orientation of the plane. 10 N/mm² 30 N/mm² 50 N/mm² 2007 50 N/mm² 30 N/mm² 10 N/mm²
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2. For the 30 kN force shown, determine the deflection of B and E, respectively. 0.4 m 0.3 m B A 0.2 m OC -0.4 m 30 kN E
1. The stress condition on a two-dimensional infinitesimal material element is shown in Fig. 1 Fig. 1 60 MPа A 50 MPа В 30 MPа A. Describe the state of stress on: (i) Face A (ii) Face B B. State the sign convention for stress components on faces A and B in the: (i) Physical-space (ii) Mohr-Circle-space C. Draw the Mohr circle for the stress element in Fig. 1
2= The deformations of a body are presented as follows. Find the Cauchy strain tensor [Cij] and volumetric strain at the point of (2,1,1) and at the time of t* sec. x₁ = (2¹-1) X₁ +α X3 ) + X₁, a X₂ = X3 (2¹-2-¹) + X2, X3 = X3. İ 0.5 0.5
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
Situation 10: The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress-free. The temperature in the steel rod is decreased by 40°C. Neglect the weight of the bar Steel L = 910 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/C AT = -45°C 0.5 m + 1.3 m Aluminum L = 1320 mm A 1200 mm² E = 70 GPa a = 23 x 106/C 27. Determine the stress in the aluminum rod 28. Determine the stress in the steel rod 29. Determine the deflection at the point where aluminum rod and bar is attach