Velocity higher education* ASSIGNINENT15070402)-3-090Q1E2204020406QUESTION 1: DYNAMICSHCENCA1.1Define the following terms:1.1.1Distance and give its Sl-unit1.1.2Velocity and give its Sl-unit(2 x 2)(4)A bus is moving with a constant velocity of 20 m/s for 5 s and comes to rest in3 s at the robot, which turned red.1.2Draw a fully labelled velocity – time graph of the motion of the busover its journey.1.2.1-(4)1.2.2Calculate the acceleration of the bus during its last 3 s.(2)Calculate the displacement covered by the bus throughout thejourney.1.2.3(3)(2)[151.2.4Calculate the average velocity of the bus.2204020406

Answered: QUESTION 1: DYNAMICS 1.1 Define the…

QUESTION 1: DYNAMICS 1.1 Define the following terms: 1.1.1 1.1.2 Distance and give its Sl-unit Velocity and give its Sl-unit

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

21. As water is flowing from a water tower to someone house, water is flowing at a speed of 4 m/s in a pipe with diameter of 0.5 m. The pipe gradually increases to a diameter of 1.8 m and then gradually decreases to a diameter of 1.1 m. Draw neat sketch. i) what is the speed of the water when it reaches the pipe diameter of 1.1 m? ii)what is the flow rate of water flowing through the pipe in lit/hr?
What is the diameter of the pipe at L= 1,2 and 3 m from the 1-1 end
pls take setting 1 to answer pls answer as fast as possible subject:(fluid mech 2)
Fill in the blank which is given below The linear displacement can be also calculated with using the average linear velocity and
Motion
Can tutor be more clearly on why it need to times 1.5 and how to make use the formula to make it increase the velocity of Block B by 50%
CHLI) plane Giaco use your knowledge of Geometry and the Valve a = (7.92 X10-0) cm to determine the A Sur Face clensity Inclucling Units
The local Amazon warehouse is looking to increase package delivering efficiency. They are testing a new conveyor belt system. Boxes are transported from one end of the factory to the other on this conveyor belt, with a velocity of vo. They eventually reach the end of the conveyor, where they slide onto a fixed incline section with uk = 0.40. The start of the inclined section is Point A, and the end is Point B. Determine: a) The velocity of the conveyor belt if the boxes leave the incline with a velocity of 8 [ft/s] Use the following diagram. Hint: Consider a box. Find its kinetic energy at point B. Find the works done by all the applied forces to the box, from point A to B. Use principle of work and energy to find kinetic energy and velocity of the box at point A. The solution is independent of mass, but for simplicity of solution, you can consider mass as 1 slug. 20 [ft] A 15°
-Drawing the relationship between the linear displacement (x) and the angle (theta) in practice through the readings you want. The device then unifies the slope at different points of the rest diagram to practically find the values of the free velocity of the slide and draw the relationship between the linear velocity and the angle (theta), which is a sinusoidal function and be a cosine function. Note:-r=25 mm, l=150 mm.
The flow carried by pipe below discharges into the open atmosphere. If the pipe length is 300 m, diameter is 150 mm and roughness of 0.0025 mm, write the equation(s) required to determine the maximum discharge.
PLEASE ANSWER THESE 3 QUESTIONS. 1-3 1. Which type of fluid flow refers to the flow of fluid that is smooth, the path taken by each particle does not cross over one another? A.Constricted C. Turbulent B.Laminar D. Viscous 2. What type of fluid flow is marked by an example of flowing water that hits arock with great force? A.Constricted C. Turbulent B.Laminar D. Viscous 3. Which of the following is the basis of Continuity Equation? A.Second law of motion C. Conservation of momentum B.Third law of motion D. Conservation of mass
The water tank has a rectangular crack on its side having a width of 100 mm and an average opening of 0.1 mm. Laminar flow occurs through the crack. The water is at a temperature of T = 20°C. Take Pw = 998.3 kg/m³ and μw = 1.0(10-³) N. s/m². Suppose that h = 2 m, L= = 200 mm. Part A 100 mm h Determine the volumetric flow of water through the crack. Express your answer to three significant figures and include the appropriate