A 150 mm diameter pipe carries 81.3 L/s of water. The pipe branches in to two pipes one is 50 mm in diameter and the other is 75 mm. What is the velocity in 75 mm pipe if the velocity of the flow in 50 mm pipe is 10 m/s? a. 13.96 m/s b. 15.67 m/s c. 17.25 m/s d. 19.43 m/s

Q: Find the specific speed of the pump, if the discharge through the pump is 160 liters/sec, speed is…

A: Given values are, discharge Q= 160litres/sec=160×10-3m3s speed N=1000rpm ,head H=27.5 m The specific…

Q: 2- Use the following data to evaluated the sin(0.6)) (work with 4D) 0.5 1 1.5 2 2.5

A:

Q: Give the classification of flow meters

A: Flow meters can be classified into two categories - Mass flow meters Volume flow meters

Q: 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The flow direction is from 2 to 1 if AZ…

A:

Q: where do v sub 1 came from? which is 0.95m/s

A:

Q: As water is flowing from a water tower to someone house, water is flowing at a speed of 3 m/s in a…

A: Water velocity at 0.3 m diameter, V1=3 m/s Gradual increase in diameter, d2=1.8m Gradual decrease in…

Q: An irrigation line carries water from a lake down into an arid valley 810 ft below the surface of…

A:

Q: The air is measured at 30 deg. C and 518mm Hg. The duct diameter is 585 mm while the discharge…

A:

Q: nd the diameter of the pipe in mm. The discharge of the pipe is  20 lit/sec with the velocity of…

A: Given data: Discharge of the pipe (Q) = 20 lit/s Velocity of the water (v) = 4.75 m/s Need to…

Q: A venture-meter is shown in Figure (1) carries water, find the flow rate if there are no losses…

A:

Q: Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes.

A: Given data Discharge (Q)=0.86m^3/s  Friction factor (f) =0.02

Q: Water enters a pump through a 250 mm diameter and leaves the pump through a 150 mm diameter pipe. If…

A: To find a. Velocity of suction pipe.b. Velocity of discharge pipe.

Q: Find the wark done Farce = 2 N Displacement = 0.045m

A: Given data : Force=F Displacement=d   Required : Work done

Q: A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at…

A:

Q: A Fluid flows at a velocity of 225 cm/s in a pipe with flow rate of 89.3 Litres/sec. then find…

A: Given data Velocity (v) = 225 cm/s = 2.25 m/s Flow rate (Q) = 89.3 lit/sec = 89.3 x 10-3 m3/s

Q: ith a velovity of 2ft/s. What is the kinwtic energy of the water in ft.lbf/lbm?

A: given:velocity v= 2ft/sdiameter d=1.5in

Q: m before the bend to 0.4 m after it. Water enters the bend at the rate of 0.5 m3/s with a pressure…

A:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

A:

Q: a. 207,967.94 N/m b. 208,968.98 N/m c. 209,978.96 N/m d. 209,979.00 N/m

A:

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: Two inward flow to

A: 437 RPM

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A:

Q: What is the velocity of the pipe center (m/s)? Given that h3=68.9 cm h2 =7 cm h =3 cm Water .

A: given data: difference in head at pitot tube be h; according the question h = h3 h = 0.689m taking,…

Q: What is the velocity of the pipe center (m/s)? Given that h3=47.1 cm hy =7 cm h =3 cm Water

A: Solution:

Q: In the venturimeter experiment the actual discharge is measured using a flow meter in

A: In the venturimeter experiment, the actual discharge is measured using a flow meter in

Q: Guava juice enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft3 / hr, then exits through a…

A:

Q: Looking for the calculations / unit analysis for ... 1.) Inlet Potential Energy 2.) Outlet…

A: Given that, Rate of water, Q=60 GPM,Diameter of water, D=2 in,Elevation of pipe, h=100 ft,Pressure…

Q: What is the pipe velocity at point 12 Given the specific gravity of pink liquid S=3.9 and height…

A: Given    Height, h = 0.4 m

Q: A water system of 2 inches (inside diameter) pipe, having a length of 1/4mile, is to be flushed with…

A: Given Data: The inside diameter of the pipe is, d=2 in=2 in×ft12 in=16 ft. The length of the pipe…

Q: Show in Figure 1 is the water flow system. The velocity head difference is = 2.0m. Volume flow rate…

A: Given data as per the question velocity head =2 m volume flow rate =0.5 m3/s h1 =1 m h2 =2 m hA = 3…

Q: 2 Oil flows from a tank through a 50 mm diameter pipe. If the average velocity is 1,3 m/s, determine…

A:

Q: Guide Questions: 1. In your own words, how will you describe a microcontroller? 2. What is the role…

A: 1.how will you describe a microcontroller? A microcontroller is a  computer present during a single…

Q: A gear pump delivers fluid at 20 m³/s to a 3 mm diameter double-acting hydraulic cylinder. If the…

A:

Q: ! A B C D =150 mm 4-50 mm 1,5 m 3,6 m 2,4 m

A: given; vertical distance from point C to B (h1)=1.5mvertical distance from point C to D…

Q: Q1: If flow rate in pipe shown is (0.5m'/s) find the (H). H. water D=300 mm

A: Given data Volume flow rate = Q = 0.5 m3/sDiameter of pipe = 300 mm = 0.3 m

Q: Estimate the velocity needed to achieve the intermittent flow of water on a pipe where flow length…

A: Given   Height, h = 74.67 centimeters                  = 0.7467 m

Q: A water system of 2 inches (inside diameter) pipe, having a length of 1/4mile, is to be flushed with…

A: Given data: Inside diameter of the pipe, d = 2 in. Length of the pipe, L = 1/4 mi. Calculate the…

Q: Three arterioles of the same length are in parallel and connected to an artery. The flow rate in the…

A: the flow rate through arteries = Q = 300 ml/min flow rate through constricted arteries = Q3 = 50…

Q: Water is flowing in a 2.5-in.-diameter pipe at 60 ft/sec. If the pipe enlarges to a diameter of 5…

A:

Q: The ratio of actual discharge to theoretical discharge through an orifice is coefficient of…

A: Given,  In the given statement it is asked If the ratio of actual discharge to theoretical discharge…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.