I need it handwritten and all the parts I'll rate but pls all and correct Question (1)power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm.The coefficient of friction for the threads is 0.13 and that for the collar is 0.1 which has aneffective diameter of 90 mm. This power screw is required to raise a load of 70 kN at a screwrotational speed of 2 revolutions per second. Circle the correct answer in the following:A b) The lead for the screw is:(а) 6 mmc) The root (minor) diameter is:(а) 36 mm(b) 12 mm(c) 3 mm(d) 1.5 mm(b) 30 mm(c) 33 mm(d) 34.5 mmd) The torque required to raise the load is:(a) 533.6 N.m (b) 553.5 N.m (c) 218.64 N.me) The power required to raise the load is:(a) 6.95 kW (b) 6.7 kW(d) 315 N.m(c) 2.75 kW(d) 3.95 kWh land hy 1 m?:

Answered: Image /qna-images/answer/4a13a1ff-5914-4c0a-92ee-4cd5daa8d286.jpg

Question (1) A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The coefficient of friction for the threads is 0.13 and that for the collar is 0.1 which has an effective diameter of 90 mm. This power screw is required to raise a load of 70 kN at a screw noond Circle the correct answer in the following:

Question (1) A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The coefficient of friction for the threads is 0.13 and that for the collar is 0.1 which has an effective diameter of 90 mm. This power screw is required to raise a load of 70 kN at a screw noond Circle the correct answer in the following:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answers to questions 4, 5, and 6 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.
If the answer is no can anything be done to save the part?
Can I get the Top, Side and views. Using free-hand drawing of this coupling pieces..
Why did we subtract fx
1. What revision is this part on? 2. How many dimensions are expressed using the limit method? 3. What is the surface texture in microinches is specified for the cylinder surface with a maximum material condition of 1.250"? Leave out the units, it is microinches, just type the number. Thanks :)!
When do the actual dimensions occur?
Refer to the Ø.8740 ± .0005 dimension.A) Where is the tolerance specified ? ____________________________ B) Is its tolerance unilateral or bilaterial ? _________________________ C) What is its tolerance ? _____________________________________ D) What is the MMC, ? ________________________________ E) What is the LMC,? _________________________________
solve question 2
a) Name two groups of standards in addition to national, industry-wide standards and where they are valid. b) Which three options exist for defining dimensional tolerances in a technical drawing?
This course A material having a shear modulus G, is deformed under a pure shear stress as shown in the following figure. Calculate the applied shear stress. Given: a = 1 mm, b Consider a linear elastic behavior. = 200 mm and G = 1.5 GPa. a 四

Vernier Caliper with 50 divisions (lines) on the vernier scale, then the least count is
5. Which of the following is the correct sequence of the ability of the machining process to produce fine tolerances (best to worst) Lapping. Grinding, Reaming, Milling Grinding, Lapping, Milling, Reaming Grinding, Milling, Lapping, Reaming Lapping, Grinding; Milling, Reaming a. b. C. d.