Indicate the following technical tolerance requirements in Fig.3.a) The diameter of the middle cylinder is Odh7, use Enveloperequirement;b) Cylindricity tolerance of d is 0.009mm, straightness of axis of odis $0.012mm;c) Total run-out tolerance of right end surfaces related to axis of Pdis 0.01 mm;d) The surface of od cylinder is obtained by the method of removingmaterial, and the maximum allowable value of Rz is 0.4µm. Allsurfaces are obtained by the method of removing material, and allthe roughness Ra allowable value is 6.4 pm.

Answered: Image /qna-images/answer/12011f3c-fd53-4794-b042-a407383145a5.jpg

Indicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle cylinder is Odh7, use Envelope requirement; b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od is $0.012mm; c) Total run-out tolerance of right end surfaces related to axis of od is 0.01 mm; d) The surface of od cylinder is obtained by the method of removing material, and the maximum allowable value of Rz is 0.4um. All surfaces are obtained by the method of removing material, and all the roughness Ra allowable value is 6.4 um.

Indicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle cylinder is Odh7, use Envelope requirement; b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od is $0.012mm; c) Total run-out tolerance of right end surfaces related to axis of od is 0.01 mm; d) The surface of od cylinder is obtained by the method of removing material, and the maximum allowable value of Rz is 0.4um. All surfaces are obtained by the method of removing material, and all the roughness Ra allowable value is 6.4 um.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 24R: What is a dimensioning tolerance?

See similar textbooks

Similar questions

What is the orientation geometric tolerance that is applied to this feature?: __________ Does the tolerance control a surface, axis, or center plane?: __________ What is the applied tolerance if the feature is produced at MMC?: __________
Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When calculating the limit tolerances for features that mate with purchased parts, the purchased part size must be known. This may be obtained be requesting a drawing from a vendor or, a caliper or micrometer can be used to obtain an accurate size. A shaft diameter of 1.2500" is to be pressed into a part using a FN3 interference (force) fit. Limits of size for the shaft diameter are 1.2500" and 1.2495". Determine the Limits of the hole diameter. Show all work.
Given the following sentence descriptions of the geometric tolerance information, correctly sketch the feature control frames for each and include in your lab report. i. The planar surface must be parallel within a thousandth of an inch tolerance zone relative to datum feature A. ii. The axis of a cylinder must be perpendicular within one- hundredth of a millimeter cylindrical tolerance zone at maximum material condition relative to datum feature D. iii. The total runout of the surface must be within a five- hundredths of a millimeter tolerance zone relative to datum feature A. 13 iv. The total surface profile of the surface must be within a two-thousandths of an inch tolerance zone relative to datum feature A. v. The axis of a hole must be positioned within a five- thousandths of a millimeter cylindrical tolerance zone at maximum material condition relative to primary datum feature D, secondary datum feature E, and tertiary datum feature F.
Apply a perpendicularity tolerance to control the pin within a 0.015" cylindrical tolerance zone at MMC relative to datum surface. Pin length is 1.000", base diameter is 2.000". Finish the print. +.002 -.001 te -0.375 Datum Feature
Perpendicularity tolrance that results in a virtual condition for pin/hole.
I need help with question number 15 that is pertaining to the print provided.
How many dimensions on this print express the tolerance using the limit method? (Note:exclude thread notes.) (Multiple Choice)A: oneB: twoC: threeD: six
Whats the formulae for temperature error %
Need solution to both questions.
I have three parts that I need answered pertaining to the print provided below. Did the person creating this print use the cylinder rule? (Multiple Choice)a. Yesb. Noc. There is no cylinder rule Not counting leader line callouts, how many cylindrical features in Section G-G are specified as linear dimensions? (Multiple Choice)a. 3b. 6c. 9d. 11 For those dimensions that have a tolerance specified, what name is given to the methodused? (Multiple Choice)a. High and low methodb. Limit methodc. Unilateral methodd. Universal method
What part provides the most manufacturing tolerance and is easiest to work with, part 1 or part 2? Explain why.
Tolerance note is given by: .XX ± .01 cm and .XXX ± .001 cm. What is the tolerance for a feature with a dimension 3.250 cm? Select one: O a. 0.02 O b. 0.001 O c. 0.015 O d. 0.01