Question 1 (a) For the 60-mm-diameter solid cylinder and loading shown, determine the maximum shearing stress. (b) Determine the inner diameter of the hollow cylinder, of 80-mm outer diameter, for which the maximum stress is the same as in part (a). 60 mm T = 5 kN m (a) T וננבו 80 T= 5 kNm (b)

Question 1 (a) For the 60-mm-diameter solid cylinder and loading shown, determine the maximum shearing stress. (b) Determine the inner diameter of the hollow cylinder, of 80-mm outer diameter, for which the maximum stress is the same as in part (a). 60 mm T = 5 kN m (a) T וננבו 80 T= 5 kNm (b)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The grain of a wooden member forms an angle of 15° with the vertical. For the state of stress shown, determine (a) the in-plane shearing stress parallel to the grain, (b) the normal stress perpendicu-lar to the grain.
2 pls answer...
A chain block is hanged on a pin which is supported by plates on both side as shown. If the maximum safe load capacity is 3000 lb, determine (a) the shearing stress on the shaft having a diameter of 1.75 in. (b) and the thickness of the plates if the bearing stress on the plates is 20% greater than the shearing stress.
1. The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow = 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. B FAB 12 kip 8 in. FBD
The compressed-air tank AB has a 250-mm outside diameter and an 8-mm wall thickness. It is fitted with a collar by which a 40-kN force P is applied at B in the horizontal direction. Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum normal stress and the maximum shearing stress at point K. (Round the final answers to one decimal place.)
PART 2: Determine the shear force acting at each of the following locations: (a) x = 0+ ft (i.e., just to the right of support A) (b) x = 14.0 ft (i,e., at point B.) (c) x = 20.5- ft (i.e., just to the left of the support C) (d) x = 20.5+ ft (i.e., just to the right of the support (C) (e)x=27.5ft Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. My Answers: Correct (a) V= 105.823 kips (b)V= -48.177 kips (c) V= -119.677 kips (d)V= 88 kips (e) V= 10.9998 kips PART 3: Determine the bending moment acting at each of the following locations: (a) x = 14.0- ft (i.e., just to the left of point B.) (b) x = 14.0+ ft(i.e., just to the right of point B.) (c) x = 20.5 ft (i.e. at point C) (d)x=27.5ft Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. My Answers: Correct (a) M = 403.522 kips-ft (b) M = 193.522 kips-ft (c) M = -352.0035 kips-ft (d) M =…
Question 3. A 4 by 4-in. wood-post BC is connected to a 1-in. diameter steel eye-bar AB to form a hoist. A load of w = 7000 Ibs is applied at point B on the hoist. (a)Determine the axial stresses in members AB and BC. (b) Determine the cross shearing stress in the 1-in. diameter bolt at point A. STEEL V -7000 lb WOOD FIG. I A
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed
The design specifications for the steel shaft AB require that the shaft acquire a strainenergy of 34 N.m as the 2.8 kN.m torque is applied. Using G = 72 GPa, determine(i) the largest inside diameter of the shaft that can be used,(ii) the corresponding maximum shearing stress in the shaft.
a. Compute the maximum shearing stress at point B in MPa. b. Compute the normal stress at point B in MPa. c. Compute the maximum compressive stress at point B in MPa. d. Compute the shearing stress at point A in MPa e. Compute the normal stress at point A in MPa.
One of the principal stresses in a two-dimensional stress system is 139 N/mm² acting on a plane A. On another plane B normal and shear stresses of 108 and 62 N/mm², respectively, act. Determine a. the angle between the planes A and B, b. the other principal stress, c. the direct stress on the plane perpendicular to plane B. Ans. (a) 26°34', (b) –16 N/mm², (c) 15 N/mm².
The cantilever beam AB will be installed so that the 60-mm side forms an angle β between 0 and 90° with the vertical. The 660-N vertical force P is applied at the center of the free end of the beam. Determine the value of β for which the normal stress at point a is a maximum and the corresponding value of that stress. (Round the final answer to two decimal places.)