1. A circular piece of wood, 90mm in diameter, is used as a compression block. Determine the axial force F that can be safely applied to the block if the compressive stress in wood is limited to 20MPA and the shearing stress parallel to the grain is limited to 5MPA. The grain makes an angle of 15 with the vertical.

1. A circular piece of wood, 90mm in diameter, is used as a compression block. Determine the axial force F that can be safely applied to the block if the compressive stress in wood is limited to 20MPA and the shearing stress parallel to the grain is limited to 5MPA. The grain makes an angle of 15 with the vertical.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please don't provide handwritten solution ......
Four plates, each being 15 mm thick, are to be connected by six bolts of 19 mm diameter as shown. Consider B = 181 mm. Assume that the force is equally distributed among the rivets. A. Determine the minimum force P (Newtons) if the allowable bolt shearing stress is 33 MPa. B. Determine the minimum force P (Newtons) if the allowable plate bearing stress is 32 MPa. C. Determine the tensile stress of the top plate (MPa) at segment a-a if the force P is 35 kN.
2. Show your solution.
3) With a given load P = 22.5 kips, two 2 in x 4 in wooden joints are glued together along the joint AB. Determine the normal and shearing stress (in psi) along the glued part.
A 15 in diameter rod is subjected to an axial tensile load of 45 kips. Compute. a. The normal stress developed on an inclined plane at an angle of 60° with the cross section of the rod. b. The maximum normal stress developed in the rod.
2. With the same given, if the members have a square cross-section with a diagonal of 11.31 cm and thickness of 1 cm, determine the axial stresses and the factors of safety on each of the member if the maximum allowable tensile strength is 60 kPa and the maximum allowable compressive strength is 70 kPa.
STRENGTH OF MATERIALS (NO LONG EXPLANTION NEEDED. RATE WILL BE GIVEN) Two blocks of wood, 50 mm wide and 20 mm thick are glued together as shown. If P is 600N, the shearing stress in the glued joint is
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8
1.2 A hollow circular short column of outside diameter 300 mm and thickness 10 mm carries a load of 1000 kN. Determine at what eccentricity along a diameter can the load be placed if the permissible stresses are 150 N/mm2 in compression and 80 N/mm2 in tension.
A steel truss structure is loaded as shown in Fig. 1. The truss members are made of A36 steel (f, = 36 ksi). All the members are made up of two 3.0"x5.0" (each) parallel flat bars. All the joints have bolt connection (pin connection), acting in double shear. The diameter of all the bolts is 3.0". Determine, •The average normal and shear stresses in bars AB, and Cl and the shear stress in pin H. •The average normal and shear strain in AB, and CI and shear strain in pin H (Given, E = 29x106 psi, G = 11x 106 psi) 4k 4k C IH or GH 8 ft A Pin H JT H 4k 6 @ 8 ft = 48 ft Fig. 1