A rec tangular piece of wood, 50 mm by 100 mm section is urad in cross Compression block shown. De termine the axial force P that can be safely applied to the block if the compressi ve strere in wood is limi ted shearing stress para llel to the grain ir limited angle of 20° with the horizontal. as to 20 Mpa and the to 5 Mpa. The grain ma kes an 37° 100 mm

A rec tangular piece of wood, 50 mm by 100 mm section is urad in cross Compression block shown. De termine the axial force P that can be safely applied to the block if the compressi ve strere in wood is limi ted shearing stress para llel to the grain ir limited angle of 20° with the horizontal. as to 20 Mpa and the to 5 Mpa. The grain ma kes an 37° 100 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing a force R at Point B, the deflection of the beam consists of two parts,i.e. Part I- the deflection caused by MB ; Part II- the deflection caused by R Please treat R, w, h , L , E as variables in this step , the mathematical equation for the deflection at Point B caused by R ( Part II) can be written as (Hint : to input equation R2LQ2wh , you can type (R^2*L)/(Q^2*w*h) ) b) Using the provided data: cross-section width w = 20 mm, cross-section hight h = 93 mm, length of the beam L =3 m , beam material’s Young’s modulus Q =226 GPa, applied bending moment MB = 11 kN.m The value of the deflection at Point B caused by MB ( Part I) can be calculated as ......(in mm)
hello, where did you get the values from the first equation in step 2? and also, what formula did you use for this? thank you :)
Q2:-Choose the Correct answer. (1):- Grain growth in size (recrystallization) occurs at a- Hot-forming process b- Cold-forming process c- Warm- forming process (2):- The (Vent) is a small opening in the mold to facilitate escape of a- Air and Gases b- Metal e- Sand d-Water (3):- In the Tube Drawing Process, Dies are made of a- Hard Steel b- Copper e- Aluminum d- Wood (4):- The channel through which the molten metal enters the mold cavity called a a- Gate b- Runner e- Riser d- Chaplets (5):- In pressure Die-casting molten metal forced to cavity under a- High pressure b- Low pressure c- Medium pressure d- No pressure (6):- In Electric-Arc Furnaces charge is melted by heat generated from a- Electric are High power b- Electric are Low power e- Laser d- Charcoal (7):- The Hot-chamber die-casting it is limited to use with a- High-melting point metals b- low-melting point metals e- Both
DUE NOW. Please answer it correctly and as immediately as possible. Thank you!
could you plz take a photo of the solution, the solution above isn't clear, the words are all put together so i can't quite get it.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
The forces, whose lines of action are parallel to each other and act in the same directions, are known as .A Coplanar concurrent forces .B Coplanar non-concurrent forces .c Like parallel forces .D Unlike parallel forces
(4) You are interviewing for a job as a see-saw designer. In order to get the job, you must solve a design problem involving a meter-stick with two masses hanging on it (see below). The system is to be perfectly balanced, with the pivot point offset from the center of the meter-stick. The mass of the meter-stick is 65.22 g. To get the job, you must find the unknown mass, m, in grams. 1.00 m F- Fplankt FuiOck, t Foluck0 27.0 cm 13.0 cm 65.22g 500. g 0.63096 나.9 massmissing T= 0,63896(1.0) +.500(-27) +.60 (F) = 0 13.16 grams f =1.289N = 0.1316 9.8 (5) The diagrams show a Fn stationary cargo plane Fn1 Fn2 before and after loading it. What probably happened to make the plane's center of Axis Axis Fg V Fg gravity shift as shown? tne center of gravity moveg tuwaras rne nevavlek Side of tre piane
2: The first law of thermodynamics can be written as: TdS = dU + PdV = dU = TdS – PdV. Moreover, we also use some other thermodynamic potentials. Most common three are: Helmholtz free energy: F = U – TS, Gibbs free energy: G = F + PV, Enthalpy: H = U + PV. From here prove the following: dF = -SdT – PdV, dG = -SdT +VdP, %3D dH = TdS + VdP. %3D
i need the answer quickly
3. A stone is dropped from the top of a building and hits the ground 7seconds later. How tall is the building?
4. Please provide full body diagram with explanation