A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.8 MPa. Answer must be in kN/m. Given: b 130 mm and d = 170 mm.

Q: A 20 ft long simply supported beam has 15-inch outside diameter with 1-inch-thick circular section.…

A: Givensimply supported beamL=20ftD=15in=1.25ftt=1in=0.0833 ftq1=10 lb/ftP1=15lb

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A: Given Data: Diameter of the circular cross-section, d=18 mm Shear force, V=25 kN

Q: A rigid T-frame of 300Kg and mass center at G shown is made of steel (Est= 200GPA). The link BC has…

A:

Q: 43. A semi-circular arch with a radius of 1 m is subjected to a concentrated load of 2.8 kN at point…

A:

Q: Q2: From the truss shown, determine the maximum load P (nearest Ib) that pins C and D can carry if…

A:

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A: Given:d=12 mmV=26 KN

Q: Determine the bending stress (in psi) of wire rope with drum diameter of 10 inches and wire diameter…

A: Given data Radius of curvature (R)=10 in Wire diameter (d)=0.1 in Wire radius(r)=0.05in Young…

Q: The cross section of a beam loaded with V=20.1 kN is shown. Determine the shear stress at point A…

A:

Q: the pins at A and B if the allowable normal stress for member BC is Oallow = 35 ksi and the…

A: Handwritten.jpg

Q: In the cantilever beam shown is 2 m long and the beam is cantilever. The load is 35 N and the cross…

A: Given data, Applied point at the free end, P = 35 N Dimensions of the cross-section, b = 0.03 m and…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A:

Q: For the beam shown, determine the average shear stress and shear strain in bolts at joints A and B.…

A:

Q: A high-strength steel [E = 232 GPa] tube having an outside diameter of 86 mm and a wall thickness of…

A: Given: Youngs modulus of the steel: →E=232 GPa=232000 MPa Radius of curvature: →R=50 m Outside…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: Determine the maximum shearing stress of the beam shown in the above problem (prob. #2)

A: From the moment equilibrium about the point on the right support. From the vertical equilibrium of…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: 2) A rigid beam AB rests on the two short posts as shown. Post AC is made from steel and has a…

A:

Q: The simply supported beam is built up from three boards by nailing them together as shown. Im 1 m…

A: find the allowable spacing of the nails.

Q: 5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E =…

A: GivenEs=200GPaEal=70GPadst=25mmdal=40mm

Q: The material used for section CB of the shaft shown has an allowable shear stress of Tallow= 75 MPa.…

A: Data given -

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: An 8-m cantilever beam has a uniformly distributed load of 12 kN.m throughout its entire length and…

A:

Q: What is the shear in member BC to the nearest 0.1k? L1 = 9 ft L2 = 8 ft L3 = 12 ft P = 7 k Pc =…

A:

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=88 kNe=0.025 mb=0.180 md=0.240 m

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: Two wooden planks, each 20 mm. thick and 150 mm wide, are joined by the glued mortise P joint shown.…

A: Given:

Q: 5 in. 2. Two wooden members of uniform rectangular cross section are joined by a glued scarf splice…

A:

Q: 16 kN 125 mm 3. The two boards are joined by plywood splices that are fully glued on the surfaces in…

A:

Q: 3) The control arm is subjected to the loading shown in Figure. Determine to the nearest 5mm the…

A:

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 10 mm. Assume…

A:

Q: The wooden members' A and B are to be joined by plywood splice plates that will be fully glued on…

A:

Q: -ly supported over a span of 3.0 e the breadth, and the bending st he the cross-sectional dimensions

A:

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

A:

Q: For the frame shown, determine the minimum bolt diameter at B if the shear stress in the bolt is…

A:

Q: 3) With a given load P = 22.5 kips, two 2 in x 4 in wooden joints are glued together along the joint…

A: