Question 1A circular shaft A-B-C is hollow and is acted upon by a load P,=7,565 N at the topmost part. A secondary load is P, and is uniformly distributed around the cap plateat B. The diameters and thicknesses of the upper and lower parts of the shafts are dar=31.75mm, tag=12.7 mm, dec=57.15 mm, and tec=9.525 mm, respectively(a) Evaluate the normal stress o AR in the upper part of the shaft(b) The designer desired that the lower portion of the circular shaft to have the same compressive stress as the upper portion, what should be the magnitude of theload P2(c) If P, should remain at 7,565 N and P2 is now set at 10,057 N, What new thickness of BC will result in the same compressive stress in both parts?

Answered: Image /qna-images/answer/03eb909d-87b3-42e4-bdd2-7a71b2617018.jpg

Question 1 A circular shaft A-B-C is hollow and is acted upon by a load P=7,565 N at the topmost part. A secondary load is P, and is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the shafts are dan=31.75mm, tag=12.7 mm, dec=57.15 mm, and tec=9.525 mm, respectively (a) Evaluate the normal stress a An in the upper part of the shaft (b) The designer desired that the lower portion of the circular shaft to have the same compressive stress as the upper portion, what should be the magnitude of the load P2 () If P, should remain at 7,565 N and P2 is now set at 10,057 N, What new thickness of BC will result in the same compressive stress in both parts?

Question 1 A circular shaft A-B-C is hollow and is acted upon by a load P=7,565 N at the topmost part. A secondary load is P, and is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the shafts are dan=31.75mm, tag=12.7 mm, dec=57.15 mm, and tec=9.525 mm, respectively (a) Evaluate the normal stress a An in the upper part of the shaft (b) The designer desired that the lower portion of the circular shaft to have the same compressive stress as the upper portion, what should be the magnitude of the load P2 () If P, should remain at 7,565 N and P2 is now set at 10,057 N, What new thickness of BC will result in the same compressive stress in both parts?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 7 The drill is jammed in the wall and is subjected to the torque and force shown in . Part A Part B A = -215 MPa Correct Part C ((Txy)v) ₁ = 0 MPa A X y Correct a 20 N-m Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: 125 mm Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: 400 mm Section a-a 5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N
Two shafts are made of the same material. The cross section of shaft A is a square of side b and that of shaft B is a circle of diameter b. Knowing that the shafts are subjected to the same torque, determine the ratio TA/TB of maximum shearing stresses occurring in the shafts. Refer to Table 3.1. -b- -b- ko b A Check my work B The ratio of maximum shearing stresses is TA/TB= 5
Need asap pls. Thanks.
Q3: . A crank built up from cylindrical sections by welding required a loading of 250 lb to overcome the resistance when in the post- tion shown. (a) Compute the maximum normal and shear stresses induced in the section A-A. (b) Determine the maximum shear stresses induced in parts I, II, and III. Ans. (a) (max) = 29,000 psi, T(max) = 15,000 psi (b) 10,550 psi for part I, 6880 psi for II, 15,000 psi for III --A III II 1 Dia. Dia. Fig. 2-38 250 lb 150 "Dia.
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
HW A shaft composed of Segments Ac, CD and DB fastened to rigid supports and loaded as shown, for st G=83 GN/m², for Aluminum G =28GN/m² and for br G= 35 GN/m² Determine the maximum shearing Stress developed in each Segment? Steel d=25mm 2m Ans: TB-472 N.M, TAI = 9.1 TD=700N.. Tc=300N.m Aluminum d= Semm 1.5m & ₁ B Bronze d=25mm Im
Kindly answer d, e, f, and g only.
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
M9
A hollow, metal circular pipe ABC (see figure) supports a load P, = 113.2 kips acting at the top. P1 A dAB tAB P2 B Саp plate dBC tBC A second load P, = 22 kips is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are daR = 1.75 in., tAR = 0.5 in., dar = 2.45 in., and tac = 0.375 in., respectively. The modulus of elasticity is 28,000 ksi. When both loads are fully applied, the wall thickness of pipe segment BC increases by 200 x 10-6 in. Assume the material behaves linearly elastically. (a) Find the increase in the inner diameter of pipe segment BC (in inches). in. (b) Find Poisson's ratio for the metal. (c) Find the increase in the wall thickness of pipe segment AB (in inches). in. Find the increase in the inner diameter of segment AB (in inches). in.
Class work: The two solid cylindrical steel rods AB and BC are welded together at B and loaded as shown in the figure. Knowing that the normal stress must not exceed 175MPa in rod AB and 150MPa in rod BC determine the smallest allowable values of d, and d₂. استنساخ 200 m مكتب المدير مقابل كلية الهندسة مجمع فاطمة 250 mm B 40 kN - d 30 kN
Please answer only number 1 with complete solution (all computations must be 4 decimal places)