Question 1 A 300 m ring distributor has loads as shown in Figure Q1 where distances are in metres. The resistance of each conductor is 0-2 W per 1000 metres and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. 240 V 50 A 60 60 D A B 70 70 90 90 100 A 80 60 0 70 A Answer Figure Q1.

Question 1 A 300 m ring distributor has loads as shown in Figure Q1 where distances are in metres. The resistance of each conductor is 0-2 W per 1000 metres and the loads are tapped off at points B, C and D as shown. If the distributor is fed at A at 240 V, find voltages at B, C and D. 240 V 50 A 60 60 D A B 70 70 90 90 100 A 80 60 0 70 A Answer Figure Q1.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
What will be the value of the twiddle factor: W42
. Using the I – V curves how are ohmic materials different from non-ohmic materials
helpp
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Ip Ep=40 V f = 60 Hz N₂= 20- N₁ = 120 Find the maximum flux om om = Find the magnitude of the induced secondary voltage Es Es = units + Is Es units If the coefficient of coupling (k)= 0.75, determine the magnitude of the induced secondary voltage Es Esk=0.75 = units
actice Test X SAT Practice Test #3| SAT Sui x O Magnetism Assessment Circuits Assessment Version D X om/formatives/6057e04c0e661559058a72de Maps S Advertisement 8. 9. 10 11 12 13 14 15 16 17 18 19 20 -0-O Into the page Out of the page The wire shown has a current being carried to the right and point P is a distance r away from the wire. By how much would the magnetic field change if the current was doubled and the distance r was doubled? Halved (1/2) Doubled (2x) Quartered (1/4) Quadrupled (4x) No change Search or type URL 12 4. 6 80 R Y U SO F G H. K L. command option O0O000
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation