Qó: For anchor sheet pile in sandy soil as shown in Figure beiow, Find thefollowing:y=16 kN/m3ka= 0.34 mKp=3Par4 mRa 4Dredge LinePaaDRp1- Resultant of active forces, Ra and it location from anchor force, y2- The depth of zero shear force, a3- The value, x and the depth of embedded sheet pile, D4- The force in anchor, Par

The wall given is : The given wall is an anchored sheet pile wall.

Answered: Qó: For anchor sheet pile in sandy soll…

Qó: For anchor sheet pile in sandy soll as shown in Figure below, Find the following: y=16 kN/m ka= 0.3 Kp=3 Par 4 m 4 m Ra 4 Dredge Line, Pa a Rp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3.8 The soil profi le at a site for an offshore structure is shown in Figure P13.8. The height of…

A: Given:- The height of the pile above the sand surface = 15 m The diameter of the pile = 1.25 m The…

Q: Profile of a weir on permeable foundation is shown in figure I and an elementary profile of…

A: Given- The uplift pressure heads (h) at key points Q, R and S are 3.14 m, 2.75 m and 0 m,…

Q: A weir on a permeable foundation with downstream sheet pile is shown in the figure below. The exit…

A: The given figure is shown below:

Q: 2. For the sheet pile shown below, find the maximum upstream water height when considering the…

A: Given: Flownet No of flow channels = 4 No of equipotential drops = 6

Q: A single row of sheet piles is driven into a permeable layer as shown in the figure. Given: H, = 7 m…

Q: 9.27 The plan of a group pile is shown in Figure P9.27. Assume that the piles are embedded in a…

Q: For the sheet pile condition shown in the figure, find the depth below the drec net pressure equals…

A: Ka=1-sinϕ1+sinϕ=1-sin 301+ sin 30⇒Ka=0.33also,Kp=1+sinϕ1-sinϕ=1+sin 301-sin 30⇒Kp=3…

Q: A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is…

A: The length of the pile is .The diameter of the piles is .Total column load is .Shaft resistance is…

Q: for Pile shown in fig. below, Sind Qu дозжазм 3m XX =30 S=0.84 Sand Ks=1.3 16 kN F Q=36 Sand G= 0.74…

A: Given, Ap = 0.3 x 0.3 = 0.09 m2 L = 10 m

Q: Sheet pile k= 4 x 10-4 cm/sec Impermeable layer Figure 8.23 8.2 Draw a flow net for the single row…

A: Given:- The value of k = 4×10-4 cm/sec The value of H1 = 3 m The value of H2 = 0.5 m The value of D…

Q: 5.18 A cut is made in a stiff, saturated clay that is underlain by a layer of sand. What should be…

A: To find the height of the water (hw) -

Q: Design cantilever sheet-pile wall penetrating a granular soil. a. What is the depth of the…

Q: 12.16 Consider a continuous flight auger pile in a sandy soil de- posit 10 m long with a diameter of…

A: Consider the given dataCalculate the upper limit of the standard penetration numberCalculate the…

Q: For the group of piles shown in Figure 2, determine the safe length of piles.

A: To determine- Safe length of the pile.

Q: Redo Problem 9.23 assuming that the water table coincides with the top of the fill and that…

A: Solution Calculate the total downward drag force or negative skin friction using the following…

Q: A bored pile is shown in the figure. The diameter of the pile is 60 cm. Calculate the ultimate…

A: Given data:- Diameter of the pile, D = 60 cm = 0.6 m Assume Dcr = 20×D The soil motion angle, δ =…

Q: Draw a flow net for a single row of sheet piles driven into a permeable layer as show in Figure Q3…

A: Given: k=3.19×10-4cm/secH1=9.6mH2=3.7mD=5mD1=13mAs we know the seepage losses per metre length of…

Q: 5- Determine the factor of safety against heave on the downstream side of the single-row sheet pile…

A: Factor of safety: Ultimate Load (Strength)/Allowable Load=Safety Factor (Stress) The permissible…

Q: 12.36 Figure P12.36 shows a 3× 5 pile group consisting of 15 concrete piles of 400 mm diameter and…

A: Consider free body diagram;

Q: A 30 cm diameter concrete pile is driven into a homogeneous consolidated clay deposit (C = 40 kPa, a…

Q: d. Starting out from the condition where the water table is above the excavation line on both sides…

A: Brief concept introduction- Sheet Pile- Sheet piles are used to support earth retention and…

Q: calculate the factor of safety against heave,

Q: Q-7 The following figure shows the flow net for seepage of water around a single row of sheet piles…

Q: A driven closed-ended pile, circular in cross section, is shown in Figure P 9.4.Calculate the…

A: Given:- Irr = 50. c'=0 width =381mm To find:- a. The ultimate point load using Meyerhof’s…

Q: A steel pipe pile of 61 cm outside diameter with a wall thickness of 2.5 cm is driven into loose…

Q: PROBLEM 2: A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The…

Q: The flownet for seepage of water around a single row of sheet piles d into a permeable layer is…

Q: ed in a layer of sand. The following is an approximation penetration resistance (q.) and the…

A: Given:- pile size=0.406m x 0.406m L=18.3m FS=4 To find:- allowable bearing capacity of the pile

Q: A construction project of cantilever sheet pile penetrating saturated clay is designed to form a…

A: Given…

Q: D 7.0m. 2.0m Yt = 16.5 kN/m³ $' = 30° Loose sand fill: Yt = 19.5 kN/m3 $' = 30° Dense sand: Yt = 21…

A: The surcharge is equal to 10 KPa.Unit weight of water = 10 KN/m³for loose sand = 0.3 and for dense…

Q: For the pile cap shown, find the maximum allowable load (V) if F.S. = 2 and maximum allowable…

Q: In-situ stresses – Seepage condition ground level sheet piling Example: For the sheet pile which T…

A: Consider the given data Yd=18 kN/m3Ysat=20 kN/m3Yw=10 kN/m2 Calculate total stress and effective…

Q: 7. If a 45 cm diameter pipe pile is driven into clayey soil to a depth of 12 m. (a) what would the…

A: Given, D = 45 cm or 0.45 m L = 12 m ϕR = 30o

Q: Problem 1 Pre-stressed concrete piles are planned for use as the foundation for a waterfront…

A: Given data in question Unit weight Side of pile Length Constant values To find out Skin friction…

Q: 1) A precast concrete pile with a cross-section of 350mm x 350mm is embedded in sand. The length of…

A: The given information is Size of pile350×350mm φ=350 L=15 m γsand=15.8 kN/m2 The relative density…

Q: A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The soil has…

Q: n-situ stresses - Seepage condition xample: For the sheet pile which uried in sandy soil ,shown in…

A: The given data is: The water level is situated at the depth=2 m Assume, the dry unit weight of the…

Q: 4. For the cantilever sheet pile wall, compute the depth of Embedment of sheet pile by the…

Q: A SINGLE VERTICAL FRICTION PILE OF DIAMETER 500 MM AND LENGTH 20 M IS SUBJECTED TO A VERTICAL…

A: Introduction: According to Terzaghi's theory, a foundation is said to be deep when the depth of the…

Q: A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven…

Q: A circular pile of diameter 0.6 m and length 8 m was constructed in a cohesive soil stratum having…

Q: A 500 mm diameter and 25 m long driven concrete pile carries a column load of 1600 kN. It is…

A: Solution Given data Es= 18 MPa Ep= 32000 MPa μs=0.2 Length= 25 m Diameter = 500 mm

Q: 12.2 A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Q, by a.…

A: Required: Ultimate Point Load, Qp a. Meyerhof's Method b. Vesic's Method (m=600) c. Coyle and…

Q: Q: The following figure shows the flownet for seepage of water around a single row of sheet piles…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

Qó: For anchor sheet pile in sandy soil as shown in Figure beiow, Find the
following:
y=16 kN/m3
ka= 0.3
4 m
Kp=3
Par
4 m
Ra 4
Dredge Line
Pa
a
D
Rp
1- Resultant of active forces, Ra and it location from anchor force, y
2- The depth of zero shear force, a
3- The value, x and the depth of embedded sheet pile, D
4- The force in anchor, Par

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Analysis of wall by using given pressure distribution:

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Flow Nets A single row of sheet piles is driven into a permeable layer as shown in the figure. Given: • Hị = 5.5 m • H2 = 4.4 m Calculate the seepage loss per meter length of the sheet pile (at right angles to the cross section shown). Bear in mind that in the flow net of the system the number of flow channels is Nf = 4 and the number of potential drops is Na = 8. + Sheet pile H H2 D k = 4 × 10-4 cm/sec Impermeable layer Round your final answer to three significant figures. ® m³/ day /m 1.
7. If a 45 cm diameter pipe pile is driven into clayey soil to a depth of 12 m. (a) what would the allowable load capacity (Q) be? The water table is 2 m below the ground surface and the soil profile consists of two clay layers (refer to the figure below). Use the ß method to calculate skin friction and the R=30° for all clay layers. (b) Explain how you selected FS value you use. 12 m ▶ 9m 2m 45 cm Y = 18.5kN/m³ = 30kN/m² Ysat = 19kN/m³ C₂ = 30kN/m² Ysat = 20kN/m² S = 60kN/m²
Evaluate the resisting capacity against axial load due skin friction of a concrete pile embedded into a layer of plastic clay given in the following conditions: Size of pile = 0.4 m square Depth of penetratian inta the clay layer = 40 m Unconfined compression strength (qu) af the clay = 200 KPa Ans. 6400 kN
Q-4: The following figure shows the flow net for seepage of water around a single row of sheet piles driven into a permeable layer. Calculate how deep the sheet pile should be driven (h) to achieve factor of safety = 3 against downstream heave, given that ysat for the permeable layer = 18 kN/m3. (Note: Thickness of permeable layer T = 18 m) H₁ = 10 m (h) Heave zone Sheet pile ►||1| Impermeable layer H₂ = 2 m Ysat 18 kN/m³
In-situ stresses-Seepage condition ground level sheet Example: For the sheet pile which T is buried in sandy soil ,shown in 2.0m the figure below, find the total piling. water level and effective vertical stress at Points 0, 6, and 12?. 4.0m Note: Assume reasonable values for saturated and dry unit weight equipotential datum oollege Of I of the soil 3.0m flow line 3.0m Soil Mechanics : Lecture 2
A 28m free-head group piles (7 * 7) with diameter of 320mm and a spacing of 1200mm each. The piles were constructed in a saturated clay layer with cohesion of 90KN / (m ^ 2) and T = 20KN / (m ^ 3) Find deflection of the piles under a lateral group load of 350KN. The load is at the ground surface. Clay has Su=100KN/m^ 2 EpRx=5O
Draw a flow net for the single row of sheet piles driven into a permeable layer as shown in Figure below Given: H₁ = 3 m H₂ = 0.5m calculate the seepage loss per meter length of the sheet pile (at right angles to the cross section shown). H₁ 3 D = 1.5 m D₁ = 3.75 m D₁ -Sheet pile k= 4 x 10-4cm/sec Impermeable layer
A 30 cm diameter pile is driven 10 m deep into a homogeneous consolidated clay deposit. The safe load carrying capacity (in kN) against the factor of safety of 2.5. Take unit cohesion of clay as 40 kN/m² and adhesion factor as 0.7. A 150.8 B 105.6 C 215.4 D 115.7
A pile with a diameter of 40cm and a length of 15m is intended for the sandy soil. If the standard tube test around the pile is homogeneous with N = 30, find the tip support and friction support of the pile. ans Qs=1507.2kn Qp=1130.4kn
Determine the design capacity of the concrete pile shown in Figure 3 for a factor of safety of 2. 2 Design = ? |VIAYIAY/YIAVAVIAVA Groundwater Table 6 m Dense Sand 20 m y = 20.45 kN/m O = 37* K = 0.90 0.5 m Điameter
Q6) Find the ultimate compressive (Qu) and pullout (Tu) capacities of the driven closed-end steel pipe-pile shown in Fig. (6). Given data: outer diameter = 610 mm weight of empty pipe = 186.8 kg/m a = 1 for cu ≤ 25 kPa ぬ。 34 35 36 Disp. Piles 41.3 49.9 60.9 Cu = 12 kN/m² Ysat = 16 kN/m³ Cu = 50 kN/m² Ysat = 18 kN/m³ c=0 Cu = 100 kN/m² Ysat = 20 kN/m³ = 35° Ysat = 20 kN/m³ 3 wall thickness = 12.7 mm pile to be filled with concrete. α = 0.5 for c₂ ≥ 75 kPa No Non-disp. Piles Fig. (6) 20.3 24.6 30.1 W.T. - Ans.: Qu= 4165 kN, T₂ = 1696 kN 6 m 4.5 m 4.5 m 6 m
4. For the system shown in the figure below: 5.0 m Datum 7.0 m 5.0 m a) Flow rate per meter length of sheet pile, if k = 1 × 10-4 m/s. b) Calculate the total stress at point A, if void ratio of the soil is equal to 0.57 and specific gravity is 2.68.