A 500 mm diameter and 25 m long driven concrete pile carries a column load of 1600 kN. It is estimated that the shaft carries 1200 kN and the point carries 400 kN. Determine the settlement of the pile head with the following data: Elastic modulus of soil, Es = 18 MPa; Elastic modulus of pile, Ep = 32,000 MPa; Poisson's ratio of the soil, Hs = 0.2; Layer thickness, H, is very deep (assume H = ∞). %3D

A 500 mm diameter and 25 m long driven concrete pile carries a column load of 1600 kN. It is estimated that the shaft carries 1200 kN and the point carries 400 kN. Determine the settlement of the pile head with the following data: Elastic modulus of soil, Es = 18 MPa; Elastic modulus of pile, Ep = 32,000 MPa; Poisson's ratio of the soil, Hs = 0.2; Layer thickness, H, is very deep (assume H = ∞). %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pile of diameter 0.4 m is fully embedded in a clay stratum having 5 layers, each 5 m thick as shown in the figure below. Assume a constant unit weight of soil as 18 kN/m³ for all the layers. Using method (= 0.15 for 25 m embedment length) and neglecting the end bearing component, the ultimate pile capacity (in kN) is G Y=18kN/m³- for all layers 7XXX 5m 5m 5m 5m 5m = 25 m 0.4m, c=40 kPa c=50 kPa c=60 kPa c=70 kPa c=80 kPa S XXXX
This question
3. A concrete pile 15.24 m long having a cross section of 406 mm × 406 mm is fully embedded in a saturated clay layer for which Ysat 19.02 kN/m³, Ø = 0, and cu=76.7 kN/m². Determine the allowable load that the pile can carry (Assuming FS-3). Use the a method to estimate the skin friction and Vesic's method for point load estimation.
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m
Q1: Determine the allowable load capacity for the driven pile of 0.6 m diameter embedded in a layered soil as shown in the figure below, use F.S 2.0 , K, = 1.5 and tand =0.5? ELEV. 110 N.C.C W.T ELEV. 108 Cu =70 kPa Y = 17 kN/m3 a = 1, yw = 10 kN/m? ELEV. 102 O.C.C, Cu 180 kPa, y = 20 kN/m³ a = 0.45 ELEV. 98 Sandy Layer Yt = 19 kN/m3 Ø = 32° Nq = 23.18 ELEV. 90
[Geotechnical design] Please finish the answer step by step and clear to see. Thank you!
A square concrete pile of 10 m length is driven into a deep layer of uniform homogeneous clay. The average unconfined compressive strength of the clay, determined through laboratory tests on undisturbed samples extracted from the clay layer, is 100 kPa. If the ultimate compressive load capacity of the driven pile is 632 kN, the required width of the pile is mm. (in integer) (Bearing capacity factor Nc = 9; adhesion factor a = 0.7)
A pile of diameter 250 mm is installed in a soil strata with a recently filled layer of clay of 3 m depth. The unit cohesion of the material is 18 kN/m² and unit weight of soil is 15 kN/m². The negative skin friction on the pile is equal to. (assume adhesion factor = 0.4)
1) A 0.5 meter diameter (D) concrete pile is driven into a sand deposit with y moist = 18.7 kN/cubic meter and o= 31 degrees. The water table is very deep. a. Assume Nq = 68.2. b. Assume K= 0.727 (Effective Earth Pressure Coefficient) c. Assume ô (friction of concrete surface to sand) = 24.8 (0.8 Tan 4) ESTIMATE PILE SHAFT ULTIMATE CAPACITY ASSUMING PILE IS 40 METERS LONG USING MEYERHOF'S METHOD. Assume critical depth is 15D. Hint: pile perimeter is 1.571 M