QN 72+A rectangular plate, 15 mm thick, made of a brittle material is shown in Figure. Calculate thestresses at each of three holes of 3, 5 and 10 mm diameter.[161.82, 167.33 and 200 N/mm ]10020 kN--20 kN25

Given: the thickness of plate, t = 15 mm The width of plate, b = 25 mm The diameter of smallest…

Answered: QN 72+ A rectangular plate, 15 mm…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 400 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?
Calculate the principal normal stresses and their directions, the maximum shear stresses and the stresses that will occur on the inclined (C) surface of the stress element whose stress state is given in the figure, by drawing a shape with the MOHR CIRCLE METHOD. Show the stresses you find in the stress element. Show the findings on the Mohr circle and, where necessary, on the element. σx= 500kg/cm^2 ,, σy=750kg/cm^2 ,, τ= τxy= τyx =300kg/cm^2 ,, α=45 degrees
Q2: Figure (2) shows an isometric view of a crankshaft that is actuated by the vertical force acting at the end of the crank (267N). The diameter of the crankshaft is (10 mm). Figure (2) 254 mm 102 mm Find: 152 mm 1. Principal stresses at points B & C. 2. Select a suitable material for the crankshaft at the Rc worse condition. 76 mm 267 N -127 mm- RA
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1550 mm, and the height of the plate is h = 2100 mm. The shear strain at A is known to be +3535 prad. Assume a = 2.6 mm. Calculate the magnitude of dimension b in the figure. h Answer: b= i e Textbook and Media Save for Later | Ta B mm X Attempts: 0 of 5 used Submit Answer
This is Mechanical Engineering. Please answer with clear work and answers. Thank you
The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If the load P on the beam causes the end C to be displaced 8 mm downward, determine the normal strain developed in wire CE. (Figure 1) ECE = Submit ▾ Part B EBD = Submit V—| ΑΣΦ Determine the normal strain developed in wire BD. Provide Feedback Request Answer ΑΣΦ vec Request Answer vec SO ? ? mm/mm mm/mm Next >
Two hard rubber blocks with Modulus of Rigidity equal to 350 kPa are used in an anti-vibration mount to support a small machine as shown below. Let a = 20 mm, b = 50 mm and c = 80 mm. Deterrmine: (a) the shearing strain in the rubber blocks when a downward deflection of 6.50 mm occurs due to P. (b) the magnitude of P. Include the figure showing the shearng strain and the FBD to support your force equation, (if there is any). Show the step by step solution.
A planar stress element has the stress state: 0₂ = 16 MPa, 0 = 44 MPa and ty = 39 MPa. Through what angle would you rotate the element to find the orientation that has zero shear stress? Units for your solution will be degrees. Ţ: Txy Tor 6 + 8
Please help. Please don't provide handwritten solution ...
Please correct solution
A solid steel bar 250 mm long is 10 mm square over part of its length, the remainder being circular with a diameter of 25 mm. A gradually applied tensile load P kN induces maximum stress in the bar of 200 MPa. The total strain energy in the bar when this stress of 200 MPa is acting is 1,3 Joule. Take E = 200 GPa Calculate : The load The length of the square portion of the bar The load that falls from a height of 8 mm and induces 1,3 Joules in the bar
Q3

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

QN 72+ A rectangular plate, 15 mm thick, made of a brittle material is shown in Figure. Calculate the stresses at each of three holes of 3, 5 and 10 mm diameter.[161.82, 167.33 and 200 N/mm ] 100 20 kN- -20 kN 25