QI- Find the power required to drive a 1.5-in power screw having double square threads with a pitch of 1/4 in. The nut is to move at a velocity of 2 in/s and move a load of F= 2.2 kips. The frictional coefficients are 0.10 for the threads and 0.15 for the collar. The frictional diameter of the collar is 2.25 in.

QI- Find the power required to drive a 1.5-in power screw having double square threads with a pitch of 1/4 in. The nut is to move at a velocity of 2 in/s and move a load of F= 2.2 kips. The frictional coefficients are 0.10 for the threads and 0.15 for the collar. The frictional diameter of the collar is 2.25 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A square thread has a pitch of 3 mm and a diameter of 15 mm. The coefficient of friction is 0.2. Calculate the torque required to rotate the screw on raising and lowering a load of 500kg
Find the efficiency and the mechanical advantage of a screw jack when raising a load, using the following data. The screw has a single-start square thread, the outer diameter of which is five times the pitch of the thread, and is rotated by a lever, the length of which, measured to the axis of the screw, is ten times the outer diameter of the screw; the coefficient of friction is 0.12. The load is free to rotate.
A 5/8 inch diameter double-thread Acme power screw with a thread coefficient of friction of 0.1 is being used to raise a load of 2,404 Ib. How much does the load move in inches to two decimal places during one full revolution of the power screw ? Selected Answer: 0.08 Correct Answer: 0.25 0.01
Please answer ASAP. I will rate helpful.
A single trapezoidal metric thread power screw is to raise a load of 60 kN. The screw has a mean diameter of 34 mm and a pitch of 5 mm. The coefficient of thread friction and collar friction are 0.15 and 0.11, respectively. The collar mean diameter is 90 mm and the screw turns at 150 rpm. Determine the total torque required to raise the load in N-m.
6- Give the suitable specifications (width, thickness and length) for an open Flat-belt system to transmit a power of (74) hp at (620) rpm to a shaft with 280 rpm. Take a safety factor of (2). The smaller pulley is 250 mm diameter and the center distance is 5 m. the belt material is leather chrome tanned and the pulleys are of cast iron working in wet condition. The belts allowable tensile stress is 4.2 MPa
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.2. The torque to increase the load and the efficiency of the screw.3. The speed of the motor (in rpm), if it is directly coupled to the screw and it is desired that the boxes rise at a speed of 30 inches/min.
A machine vice as shown in figure below ,has a single start square thread with 28 mm nominal diameter and 3 mm pitch. The outer and inner diameters of the friction collar are 62 and 50mm, respectively. The coefficients of friction for thread and collar are 0.3 and 0.3, respectively. The machinist can comfortably exert a force of 240 N on the handle at a mean radius of L= 217 mm. Assuming uniform wear for the collar, Calculate: a-Mean diameter of the screw d. b-Helix angle a. C- Friction angle 4. d-Tightening Torque T in terms of W. e- Friction Torque Tc in terms of W. f-Clamping force developed between the jaws W. g- Overall efficiency of the clamp n. Fixed jaw Moving jaw Screw Frame Handle