I need the answer quickly QI: Choose the best answer that completes the statement or answers the question.1. A basic S-R flip-flop can be constructed by cross-coupling of which basic logic gates?a) AND or OR gatesb) XOR or XNOR gatesc) NOR or NAND gatesd) AND or NOR gates2. In S-R flip-flop, if Q 0 the output is said to bea) Setb) Resetc) Previous stated) Current state3. What is one disadvantage of an S-R flip-flop?a) It has no Enable inputc) It has no clock inputb) It has a RACE conditiond) Invalid State4. Four J-K flip-flops are cascaded with their J-K inputs tied HIGH. If the input frequency (fm) tothe first flip-flop is 32 kHz, the output frequency (fout) isa) 1 kHzb) 2 kHzc) 4 kHzd) 16 kHz5. In D flip-flop, D stands fora) Distantb) Datac) Desiredd) Delay6. What happens to the parallel output word in an asynchronous binary down counter whenever aclock pulse occurs?a) The output increases by 1c) The output word inereases by 2b) The output decreases by 1d) The output word decreases by 27. How many flip-flops are required to construct a decade counter?a) 4c) 5b) 8d) 108. Three cascaded decade counters will divide the input frequeney bya) 10b) 20c) 100d) 10009. Assume that a 4-bit serial in/serial out shift register is initially clear. We wish to store the nibble1100. What will be the 4-bit patterm after the second clock pulse? (Right-most bit first)c) 0000a) 1100b) 0011d) 111110. With a 200 kHz clock frequency, eight bits can be serially entered into a shift register ina) 4 usd) 40 msb) 40 usc) 400 µs

As per our company guidelines we are supposed to answer only first 3 subpart kindly repost other…

QI: Choose the best answer that completes the statement or answers the question. 1. A basic S-R flip-flop can be constructed by cross-coupling of which basic logic gates? a) AND or OR gates b) XOR or XNOR gates c) NOR or NAND gates d) AND or NOR gates 2. In S-R flip-flop, if Q= 0 the output is said to be c) Previous state a) Set b) Reset d) Current state 3. What is one disadvantage of an S-R flip-flop? a) It has no Enable input c) It has no clock input b) It has a RACE condition d) Invalid State

QI: Choose the best answer that completes the statement or answers the question. 1. A basic S-R flip-flop can be constructed by cross-coupling of which basic logic gates? a) AND or OR gates b) XOR or XNOR gates c) NOR or NAND gates d) AND or NOR gates 2. In S-R flip-flop, if Q= 0 the output is said to be c) Previous state a) Set b) Reset d) Current state 3. What is one disadvantage of an S-R flip-flop? a) It has no Enable input c) It has no clock input b) It has a RACE condition d) Invalid State

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Help please
Question.
I need the answer as soon as possible
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
When using an oscilloscope for testing engine management systems, what is an attenuator used for? In your answer provide an example of when an attenuator should be used. (5 - 10 words)
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies