QB.38. A square tied column with a side dimension of 490 mm is reinforced with 16- 28 mm dia. bars distributed equally on all faces. The column is subjected to factored end moments of 603 and 616 kN-m without causing a sidesway. It carries an ultimate axial load of 1394 KN. The column has an unsupported height of 4.8 m. Use f'c = 20.5 MPa. Assume k = 1. Answer the following: (1) What is the relative stiffness (or El) of the column expressed in N-mm^2. (2) Calculate the moment magnifier factor if the column is bent in single curvature. (3) Compute the design moment of the column.

QB.38. A square tied column with a side dimension of 490 mm is reinforced with 16- 28 mm dia. bars distributed equally on all faces. The column is subjected to factored end moments of 603 and 616 kN-m without causing a sidesway. It carries an ultimate axial load of 1394 KN. The column has an unsupported height of 4.8 m. Use f'c = 20.5 MPa. Assume k = 1. Answer the following: (1) What is the relative stiffness (or El) of the column expressed in N-mm^2. (2) Calculate the moment magnifier factor if the column is bent in single curvature. (3) Compute the design moment of the column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the design compressive strength (kips) of a A36 steel column, W 10 X 33 with a total length of 20 feet (both pin-end connection). Use K = 1.0 and E = 29,000 ksi, Fy = 50 ksi. No need to check the local stability of the column. W10x33 ... A = 9.71 d = 9.730 tw = 0.290 bf = 7.960 tf = 0.435 rx = 4.190 ry = 1.940
The lap joint is fastened with four ¾ inch diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
A)determine determinacy and stability b) identify the zero force members
Q12. Acontinuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments.
RUSH
What is the maximum absolute shear for the following beam and load group? Use L = 21, a = 3, b = 4, P1 = 2, P2 = 4, and P3 = 4. ܢܢܢܢܢܢܢ L P₁ P2 미미 a b P3
QB.57. A square tied column with a side dimension of 420 mm is reinforced with 8- 20 mm dia. bars distributed equally on all faces. The column is subjected to factored end moments of 609 and 630 kN-m without causing a sidesway. It carries an ultimate axial load of 1002 kN. The column has an unsupported height of 4.4 m. Use f'c = 22 MPa. Assume k = 1. Answer the following: (1) What is the relative stiffness (or El) of the column expressed in N-mm^2. (2) Calculate the moment magnifier factor if the column is bent in single curvature. (3) Compute the design moment of the column.
Please answer situation 2 only
7. Design a column to support an Mx = 230 kN.m, My =140 kN.m and axial load N = 3500 kN. The 500 N/mm². Also, compute the = column is short. Assume d'/h =0.10, feu = 35 N/mm² and fy maximum axial compressive load that may be placed in the column, in combination with the moments Mr and My given above.
Please Elaborate on your solution, Thank you so much! Don't worry I'll vote your solution.
Properties 1. compute the web shear capacity a. compute the horizontal shear copacity (kN) a the JIS00 mm2 arca depth width oF Flange thickness Df Flange 350 mm Dettral axis 2I0 mm 16 mm 3. 1F the Girder was used as an 8meter long simple span capries equal concentrated dead load,P at evay quarter points and determine the load P based on shear copacity. 10 mm web thickness uniform load of 12. a KN/m, a wwgo1x クりの 45Xr0 mm? Fy 248 M Pa 4. calcubte the maximum shear it used as a 'F Fb 148 MPa 8m beam simply supportcd at the lept end and 2meter prom the right end which carries a total unitorm FV 99 MPa cocad of 45 kN/m.