Q9: The pitch of 50 mm mean diameter threaded screw of a screw jack is 12.5 mm. The coefficient of friction between the screw and the nut is 0.18. Determine the torque required on the screw to raise a load of P kN, assuming the load to rotate with the screw. Determine the ratio of the torque required to raise the load to the torque required to lower the load and also the efficiency of the machine.| Where, P= 46KN

Q9: The pitch of 50 mm mean diameter threaded screw of a screw jack is 12.5 mm. The coefficient of friction between the screw and the nut is 0.18. Determine the torque required on the screw to raise a load of P kN, assuming the load to rotate with the screw. Determine the ratio of the torque required to raise the load to the torque required to lower the load and also the efficiency of the machine.| Where, P= 46KN

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter10: Work, Energy And Machines

Section10.2: Machines

Problem 26PP

See similar textbooks

Similar questions

A load of W=40kN is lifted through a boom QRS as shown in Figure1. The boom makes an angle of 60° with the vertical. Neglect the weight of the boom and for this problem, L1 = L2 = 2m. The pulley at S is frictionless. What is the reaction at Q? Li L2 Ja R 60 W Figure 1 Q
please asap working doesnt have to be perfect
A constant 20-N force pushes a small ball in the direction of the force over a distance of 5.0 m. What is the work done by the force?
EV E Math Initial Final K, + U, + U, - W- K, - Ug+ Uy Usr + AEtherm +. t= 0.80 s ti3=D0 y= 0.70m 0- 7777 to Earth 0. Earth Mbarbell = 13.6 kg 8. The weightlifter, not in the system, raises a barbell. Energy Conservation Equation Show al Civitwar politics.. docx a At Home Friction.pptx IMG_1490jpg 2:43 PM 12/9/2020 T|||||||| ||||||| 2|||||1|1 ||L|||||| 1|||||||| 1|||||||| ||||||
26. You are using a screwdriver to screw in a screw that has a pitch of 3 cm. The screwdriver has a handle radius of 10 ст. If the efficiency is 35%, how much effort (applied) a. force is needed to overcome a resistance force of 40 N? b. What is the reason for low efficiency of the screw? Where does the energy go?
se 3: Class - Da Paco rode his skateboard up a ramp for a distance of 3.8 meters. If the ideal mechanical advantage of the is 2, how far above the ground was Paco? ramp 4: The inventor of a new machine claims that its actua mechanical advantage is 4. Literature on the machi reports its input distance is 81 meters and its outpu distance is 27 meters. Find the machine's ideal mechanical advantage, and determine whether the xar developer's claim could be true.
I included two pictures. Please show me how to approach the problem in the correct manner based on the feedback given. It is okay to completely change the answer if you need to. Please give a reasoning to why the claim is not reasonable and the work needed to back this up.
1) The Ideal Mechanical Advantage (IMA) of lever is defined as the input distance / output distance. If the input distance is 25 cm and the output distance is 5 cm, what is the IMA? a) 5 cm b) 5 cm? c) 5
b. You are tasked with inspecting the rigging to lift a 40,000 lb air conditioning unit. Assuming the load is balanced, using a 4 leg bridle hitch where the sling length is 15 ft with 8 feet of head room between the hook and the load, what would be the estimated tension on each leg of the sling when the load is lifted? What is the minimum Working Load Limit of each sling leg? What is the required sling breaking strength (assume a safety factor of 5)? 15 ft 8 ft 40,000 lbs
2600 Ihr 3. You can use a stone under a plank of wood to lift a heavy rock. State the type of machine that you can make with this equipment. i. ii. Calculate the work done by lifting a rock of weight 200N a distance 0.25m.
You’re using a system of multiple simple machines to move a 1500 N load up a height of 2 meters. You have a wheel barrow which is a combination of a lever and a wheel/axle, and you’ll be using a ramp (inclined plane). What length ramp do you need to achieve the actual mechanical advantage from using the wheel-barrow? The height is set at 2 meters. Assume the efficiency of the inclined plane (ramp) is 100% (so your ideal, or design, mechanical advantage is your actual mechanical advantage).
A system of four pulleys, two in a block is used to raise a weight of 800 pounds by a force of 200 lbs. The efficiency of the system is 80%. Draw the simple machine set-up.