Q7)The components of an electronic system are located in a 1.5-m-long horizontal ductwhose cross section is 20 cm x 20 cm. The components in the duct are not allowed tocome into direct contact with cooling air, and thus are cooled by air at 30°C flowing(1)SOFwierza-11-22over the duct with a velocity of 200 m/min. If the surfacetemperature of the duct is not to exceed 65°C, determine thetotal power rating of the electronic devices that can bemounted into the duct.DammeLore

Answered: Image /qna-images/answer/cdef815c-76d4-4b62-98e1-b72195c9cc5b.jpg

Q7) The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm x 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing (1)

Q7) The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm x 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The global average sensible heat flux is 17 W/m2. Use the following information to estimate the latent heat flux in units of W/m2. The annual global precipitation amount is about 520×1012 m3/yr. The latent heat of vaporization for water is 2.5×103 kJ/kg and the radius of the Earth is 6400 km. What is the global annual average latent heat flux?
3:10 < Back 1. Ch. 8 An 8-m-long, uninsulated square duct of cross section 0.2 m x 0.2 m and relative roughness 10³ passes through the attic space of a house. Hot air enters the duct at 1 atm and 80°C at a volume flow rate of 0.15 m³/s. The duct surface is nearly isothermal at 60°C. Determine the rate of heat loss from the duct to the attic space and the pressure difference between the inlet and outlet sections of the duct. Evaluate air properties at a bulk mean temperature of 80°C. Is this a good assumption? (Use the Moody chart if you need a friction factor.) Water 2. Ch 8 Liquid water flows at a mass flow rate of 0.7 kg/s through a concentric annulus tube with the inlet and outlet mean temperatures of 20°C and 80°C, respectively. The concentric annulus tube has inner and outer diameters of 10 mm and 100 mm, respectively. The inner tube wall is maintained with a constant surface temperature of 120°C, while the outer tube surface is insulated. Determine the length of the concentric…
A circular pipe with inner diameter of 0.02 m has its inner surface covered with water at 300K. Dry air is flowing inside the pipe at the velocity of 0.8 m/s. The temperature of air is 300K and its pressure is at 1 atm. Calculate: a) Mass transfer from the 0.01 m length pipe b) Rate of heat transfer from pipe to air by mass convection and heat convection
! Required information Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp=1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T, = 100°C D = 4 cm 2 m Q₁ = 200 W a) Determine the air temperature at the 2 m length. The air temperature at the 2 m length is b) Determine the air temperature at the exit. The air temperature at the exit is °C. c) Determine the total heat transfer to the air. The total heat transfer to the air is W.
A copper bar of circular cross-section is cooled by air. The velocity and temperature of air is 1.2 m/s and 20°C. Maximum temperature limit of copper bar is fixed and its current carrying capacity is 100 amp under given conditions. The maximum current carrying capacity of bar when velocity of air becomes three times is. Amp.
I need the answer as soon as possible
solve, show assumptions and full solutions
PROCESS INSTRUMENTATION AND CONTROL 4. A 3m X 2m window has an exterior surface temperature of 220C, and the outside wind is blowing air at -60C across it with a convection heat transfer of h= 125W/m2K. What is the total heat transfer loss?
determine the value of AB. Water is to be heated from 20°C to 70°C as it flows through a 40 mm internal diameter and 600 mm long tube. The outer surface of the tube is wrapped with electrical wire which acts as an electrical resistance heater. The heater provides uniform heat flux throughout the surface of the tube. The outer surface of the heater is well insulated. At steady state if the system provides hot water at 0.2475 kg/s, determine the power rating of the resistance heater and the inner surface temperature of the pipe at the exit. Р = 990 kg/m³; k = 0.631 W/(m K); c Pr-4.328 = 4180 J/(kg K); v = 0.66 x 10-6 m²/s:
Determine the mass flow rate (kg/s) of water that must flow through a conduit to carry 15,000 kJ/s of heat energy if the temperature difference is 10 degrees Celsius. Cp water=4.186 k*J/Kg*K
1