Q7/ Find the number of ropes required in a rope drive which is used to transmit 230 kW from a pulley of 1 m diameter running at 450 rpm. The safe pull in each rope is 800 N and mass of the rope is 0.46 kg /m length. The angle of lap is 160° whereas the angle of groove is 45°. u = 0.3.

Q7/ Find the number of ropes required in a rope drive which is used to transmit 230 kW from a pulley of 1 m diameter running at 450 rpm. The safe pull in each rope is 800 N and mass of the rope is 0.46 kg /m length. The angle of lap is 160° whereas the angle of groove is 45°. u = 0.3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A torsion dynamometer is fitted on a turbine shaft to measure the angle of twist. It is observed that the shaft twists 2° in a length of 5 m at 600 r.p.m. The shaft is solid and has a diameter of 250 mm. If the modulus of rigidity is 84 GPa, find the power transmitted by the turbine.
By moment-distribution method. Use exact values of the relative k's, whichever comes first. w1 = 25 KN/m w2 = 35 KN/m, w3 = 10.5 KN/m. 82 KN 65 KN 85 KN 70 KN 75 KN W2 W3 W1 B 120m| D 100m 2. 40 m |1.00m| 1.80 m 2.0m 1.40 m 2. 40 m 2.0 m
Q/ For the mechanism shown below, compute the magnitude of the force (F) required to break contact at point (c)? C ↑ 3 m s = 10 mm K = 1800 N/m www Q 3 m 4 m 4 m + 25 points F
Calculate the actual mechanical advantage. Calculate the system efficiency . Find the ideal ma and effort force
You want to stop the acceleration of the boxes in the figure above by applying an additional force on the system . Find the force you need to add.(Help)
Q5/ In vehicle suspension design it is desirable to minimize the mass of all components. You have been asked to select a material and dimensions for a light spring to replace the steel leaf-spring of an existing truck suspension. The existing leaf-spring is a beam, shown schematically in the figure. The new spring must have the same length L and stiffness S as the existing one, and must deflect through a maximum safe displacement 8max without failure. The width b and thickness t are free variables. L Load F 6= 1 FL³ 48 EI 10₂L² 6 #E 1=bt³/12 8max = Derive a material index for the selection of a material for this application. Note that this is a problem with two free variables: b and t; and there are two constraints, one on safe deflection 8max and the other on stiffness S. Use the two constraints to fix free variables.
Given: rA= 2.75 in, rB = 4.50 in, • Gear A: Wa= 1.1 lb, ka = 1.55 in, • Gear B: Wb= 4.4 lb, kb = 3.50 in . Moment applied to gear A= 31 lb-in change all units into feet from the start! use g = 32.2 ft/s^2 Find: B The magnitude of the force between gears A and B Fab= lb Written work, show angular accelerations of each gear Your Answer:
Find the gradient of a crawler tractor pulling a loaded rubber tire skimmer using the following information: The horsepower of the tractor is (180) horsepower. . Tractor weight (20.25) tons. The traction force of the crawler tractor in the first gear is (15300) kg. The weight of the loaded skimmer is (39.48) tons . The dirt road is not good. Rolling resistance of the tractor (73) kg / ton. The rolling resistance of the skimmer is (95) kg/ton.
Ans. RA = 9.75KN up, RB = 12.75KN up 3 m 3 m 213: Statics of Rigid Bodies Page 76 of 103 NORTHWEST SAMAR STATE UNIVERSITY STATICS OF RIGID BODIES Resiience integrity Service. Escellence 12. A rope and pulley system is used to support a body W as shown. Each pulley is free to rotate. One rope is continuous over pulleys A and B; the other is continuous over pulley C. Determine the tension T in the rope over pulleys A and B required to hold body W in equilibrium if the mass of body W is 175 kg. Ans. T= 429N arted 1 3. IN A- .
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shatt carries four masses (150 + 01) kg, (200 + 01) kg, (250 +01) kg and (300 + 01) kg. These masses are located at a distance of 1.5m, 2.5 m, 5.5 mand 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m? and mass density for the shaft material is 7500 kg/m?3. Determine critical speed of the shaft in revolutions per minute for the following two cases: 1. Effect of the mass of the shaft is neglected. 2. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
need it correctly
Calculate the torque C0 that must be applied to the handle of the screw jack in order to lift the load P= 3kN when θ = 30 ° . The screw has a pitch of 2.5 mm. Neglect the weight of the linkage.