Q6. In the circuit presented in Figure 2: (a) Calculate the Thevenin equivalent resistance between terminals A and B. (b) Calculate the Thevenin equivalent voltage between terminals A and B. (c) What is the value of the load resistance RL that must be connected for maximum power transfer to the load? R₁ E₁ 1kQ2 10V R₂ 2kQ R33KQ R4 2kQ2 Figure 2 VTH B R₁

Q6. In the circuit presented in Figure 2: (a) Calculate the Thevenin equivalent resistance between terminals A and B. (b) Calculate the Thevenin equivalent voltage between terminals A and B. (c) What is the value of the load resistance RL that must be connected for maximum power transfer to the load? R₁ E₁ 1kQ2 10V R₂ 2kQ R33KQ R4 2kQ2 Figure 2 VTH B R₁

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 19PQ

See similar textbooks

Similar questions

Currents of approximately 0.06 A can be potentially fatal. Currents in that range can make the heart fibrillate (beat in an uncontrolled manner). The resistance of a dry human body can be approximately 100 k . (a) What voltage can cause 0.06 A through a dry human body? (b) When a human body is wet, the resistance can fall to 100 . What voltage can cause harm to a wet body?
(a) F ind the voltage drop in an extension cord having a 0.0600-O resistance and through which 5.00 A is flowing. (b) A cheaper cord utilizes thinner wire and has a resistance of 0.300 O. What is the voltage drop in it when 5.00 A flows? (c) Why is the voltage to whatever appliance is being used reduced by this amount? What is the effect on the appliance?
Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off allowing a person to work on the electronics with less risk of shock, (a) What is the time constant? (b) How long will it take to reduce the voltage on the capacitor to 0.250% (5% of 5%) of its full value once discharge begins? (c) If the capacitor is charged to a voltage V0through a 100-O resistance, calculate the time it takes to rise to 0.865V0(This is about two time constants.)
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.
The resistance between terminals a and b in Figure P18.13 is 75 . If the resistors labeled R have the same value, determine R. Figure P18.13
Consider the following circuit: 15 μF 5 µF 10 µF 1. Find the equivalent capacitance of the circuit. 2. What is the charge stored by the 12 µF capacitor? 3. What is the voltage across the 5 µF capacitor? 4. What is the energy stored by the 15 µF capacitor? 20 μF 25 μ 8 µF 4 µF 12 µF IHH 40 V
1//
The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 8.5V what is V3? C R L V2 V3 21.5 V 8.5 V 15.53 V 4.5 V 13 V
PS 2: A 12-volt battery of internal resistance r of 0.05 ohm is to be recharged u, source at the rate of 8 amperes. 30-volt dc a. What resistance R is to be connected in series with the circuit? ANSWER: b. What is the terminal voltage of the battery? c. How much energy in joules is dissipated in the resistor in one hour ? ANSWER: ANSWER: