Q5: Choose the correct answer (Mcq): 1- For any rectangular section If d= 530 and c 150 mm then the strain in stad is %3D a) b) c) 0.005 0.0076 None of above 2- When the ratio of steel reinforcement exceed the maximum limit then according to ACI 318 Code, the section will be analyzed as a) Single reinforcement b) Doubly reinforcement c) None of above 3- Long direction reinforcement in one way slab is provided to carry: Bending stress Tension stress a) b) c) Temperature and shrinkage stress 4- In the shear design of rectangular beam there is a need for increasing the dimension of the beam if: a) Shear force in steel reinforcement (V.>[(2/3*VPJ*b,*d]. b) Shear force in steel reinforcement (V)-(2/3*V*°J*b,*d]. c) Shear force in steel reinforcement (V.)<{(2/3*vfJ*b_*d].

Q5: Choose the correct answer (Mcq): 1- For any rectangular section If d= 530 and c 150 mm then the strain in stad is %3D a) b) c) 0.005 0.0076 None of above 2- When the ratio of steel reinforcement exceed the maximum limit then according to ACI 318 Code, the section will be analyzed as a) Single reinforcement b) Doubly reinforcement c) None of above 3- Long direction reinforcement in one way slab is provided to carry: Bending stress Tension stress a) b) c) Temperature and shrinkage stress 4- In the shear design of rectangular beam there is a need for increasing the dimension of the beam if: a) Shear force in steel reinforcement (V.>[(2/3VPJb,d]. b) Shear force in steel reinforcement (V)-(2/3V°Jb,d]. c) Shear force in steel reinforcement (V.)<{(2/3vfJb_d].

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
Q.20 The main reinforcement in RC slab consists of 10 mm diameter bars at 100 mm c/c spacing. When 10 mm bars are replaced by 12 mm diameter bars then spacing would be
When we design doubly reinforced beams, what is the maximum possible value for Ku to get minimum area of compressive steel area? Select one: a. 0.36 b. 0.4 OC. 0.545 Od. 0.6 e. 0.8 A rectangular beam section has d = 450 mm, dsc = 45 mm and Concrete grade 40 MPa. When neutral axis depth is at its limiting depth, Ast = 3600 mm^2 and Asc = 620 mm^2 were provided to satisfy the design requirement. What is the design Moment capacity (M*) of the section? Select one: a. 692.6 kNm Ob. 584.0 kNm Oc. 466.6 kNm Od. 705.1 kNm Oe. Can not estimate without the value of 'b'
7. For a beam of cross-section, width = 230 mm and effective depth = 500 mm, the number of rebars of 12 mm diameter required to satisfy minimum tension reinforcement requirement specified by IS: 456-2000 (assuming grade of steel reinforcement as Fe500) is mi
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
1. The strain profile of the section below with compression reinforcement was calculated with a computer program. All dimensions are to center of the reinforcements. Material properties: (a) (b) (c) Concrete, f'e = 4.0 ksi Steel, fy = 60.0 ksi Is the section tension controlled? What is the strength reduction factor (p)? Check if the forces in the section are in equilibrium. Do not correct them if they are not in equilibrium. What is the nominal moment resistance of the section? (4) #9- #5@4" (5) #11. (5) #11 -24"- SECTION 3" 3" 3" 48" 0.015 0.01 0.005 Strain diagram eps ecu epst 10.035 0.01 @lowest reinforcing steel Strain Profile 0 10 20 30 40 50 60 -0.005
A singly reinforced rectangular beam has a dimension b 310 mm and d = 410 mm Factored moment is equal to 100 kN-m, Concrete compressive strength is 24 MPa, Steel yield strength is 275 MPa and the reduction factor is 0.9. Determine the required steel area in mm?
I want to solve question 1040 and the question information from question number 1039
3 نقاط The minimum reinforcement using mild steel in slab should not be less than .., if fy=420 MPa ...... 2.0% 1.8% 0.15% 0.18%
4.3 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____?____ kN/m (to the nearest whole number)