concrete beam with balanced-stress ment. 1039. Design a reinto reinforcement that will resist a bending moment of 140 kN m, assum- MPa, f, 160 MPa, and n = 8. 12 ingd=1.5b. f = 12 MPa, f Ans. b 316 mm; A, - 2110 mm² 1040. Solve Problem 1039 if b = d. simply supported 1041

Q: Activity 1. From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the…

A:

Q: Fill in the following Leveling Notes. In your handwritten notes, perform a page check and calculate…

A: Surveying is a very important branch of civil engineering as it is mainly dealt with the measurement…

Q: What is pitot tube? Briefly describe and support your explanation with appropriate equation and…

A: A Pitot tube is a pressure measurement instrument used t measure fluid flow velocity. The pitot tube…

Q: an object moving horizontally after t seconds is given by the it3 +36t2-54t, where s is measured in…

A:

Q: Solve ONLY LETTER D and E.  The first three subparts are already answered in my previous question.…

A:

Q: This is my second time asking. I cannot understand the solution of the first one I posted. Please…

A:

Q: = 6x – 0.5x y(0) = 0 y(12)= 0 Finally, Find y (4)

A:

Q: Given an adjustment containing the following: Number of Control Stations 1 Number of Unknown…

A:

Q: QUESTION 8 What is the flow of a pipe that has an 8" diameter and 1% slope? Use the Hazen Williams…

A: dia of pipe=8''slope=1%=0.01discharge=?

Q: In the figure, the cord at A is pulled down with a constant speed of 3.71 ft/s. Find the magnitude…

A: F α acceleration At A 2T α   3.71 ft/s24T α  2×3.71 ft/s2

Q: Hello. Thank u very much for this answer.   I have a little question: In this case What does Zt…

A: Given data in question  Span 50 ft Compressive force 450 kips Effective prestress 335 kips Diameter…

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A:

Q: Determine thex- and y-coordinates of the centroid of the shaded area shown. 4" 4" 6" -2.00" 2.00"…

A:

Q: Aerial photography is to be taken of a tract of land that is X-mi square. Flying height will be H ft…

A:

Q: Draw a civil engineering related line graph having one dependent variables and three predictor…

A: Answer:- 1. Line graph:-  A line graph commonly used to display change over time as a series of data…

Q: When and how long ago was the first pocket calculator invented?

A: First pocket calculator was developed in year 1971 which was invented by the Busicom.This…

Q: 7) How has smartphones chang ed communication ?

A: Smartphone technology has evolved into such a successful electronic device for instantaneous…

Q: It is assumed that no mistakes exist, and that the observations have already been corrected for all…

A: The most probable value is given by, MPV=Sum of all valuesNumber of observations The value of ν is…

Q: Don't need to show work, just need to know which ones correct to compare my answers. 3/4

A: This question is related to the Building design and drawing from Civil Engineering. In this question…

Q: Locate the centroid of the plane area shown if L = 126 mm.   the centroid of the plane area is: X…

A: There should be a range for answers. Please check onceI assumed square area as section 2 and…

Q: The following is a page of an old level field book, in which some of the missing entries are shown.…

A:

Q: A student recorded the following repeated paces of a given line: 456, 448, 462, 447, 452, 455. If…

A: Given: Pace factor= 0.628m/pace

Q: x 105 and in in. Determine Iy: Answer is in Just answer the blank space in 4 decimals 12 in 20 in

A:

Q: In a short an simple response two or three sentences. How would you say SLOs(student learning…

A: In civil engineering, the subjects are mostly related to the calculation part and other subjects…

Q: The correct answers given are: 1)  480.18 2)  28.92 Can I please have assistance to show the…

A: Torque = 6.3 kN-m or 6.3 x 106 NmmLength of the shaft = 3m or 3000 mmCross-sectional area, A= 5090…

Q: Determine 1. Coefficient Uniformity 2. Coefficient of Curvature of the table.

A: Mass retained are noted in laboratory experiment for each sieve. Total mass of soil = 2457…

Q: 4. From the given shear diagram below, where is the point of inflection located from the right end…

A: In shear force diagram point of inflection is where the sign of the shear force in shear force…

Q: 3. Draw a new arrow network by correcting the redundant dummy activity (or activities) in the…

A:

Q: The interior angles of a spherical triangle LUV and side LU were measured as follows: L= 61°45'30" U…

A:

Q: a. b. C. d. ÏÏ The most important If a mistake is found Regarding surveying having too much…

A: There are three main sources of error arise: 1) Natural error - climate, wind, humidity etc. 2)…

Q: Locate the centroid in the 'x' and'y' direction of the object below, Submit 5 points your answer…

A:

Q: Photographs at a scale of S are required to cover an area X-mi square. The camera has a focal length…

A: Area of ground=11 mi2 =11*4014489600 in2 Longitudinal overlap=60% Side overlap=30%

Q: Round every answer into 3rd SIGNIFICANT DIGIT! Round every answer into 3rd SIGNIFICANT DIGIT! Round…

A:

Q: 1) Determine the Centroid of the Shaded Area, Tabulate your answers and solution Y 450 mm 300 mm r=…

A:

Q: 1) From the following data, construct a network diagram: Activity Precedes a d,e f d. e f end end

A:

Q: The answers are wrong and I would like them in three decimal places in mm

A:

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.